[c-nsp] 7600 and WANPortLoopbackTest

[Hank Nussbacher]

I run (7613 - 12.2(18)SXD4) a diagnostic test on a specific Flexwan as follows
gp1#diagno start module 4 test all

Jul  5 10:36:15: %DIAG-SP-6-TEST_RUNNING: Module 4: Running 
TestTxPathMonitoring{ID=1} ...
Jul  5 10:36:15: %DIAG-SP-6-TEST_OK: Module 4: TestTxPathMonitoring{ID=1} 
has completed successfully
Jul  5 10:36:15: %DIAG-SP-6-TEST_RUNNING: Module 4: Running 
BusConnectivityTest{ID=2} ...
Jul  5 10:36:15: %DIAG-SP-6-TEST_OK: Module 4: BusConnectivityTest{ID=2} 
has completed successfully
Jul  5 10:36:15: %DIAG-SP-6-TEST_RUNNING: Module 4: Running Bay 1 
WANPortLoopbackTest{ID=4} ...
Jul  5 10:36:15: %DIAG-SP-3-TEST_FAIL: Module 4: Bay 1 
WANPortLoopbackTest{ID=4} has failed. Error code = 0x1
Jul  5 10:36:15: %DIAG-SP-6-TEST_RUNNING: Module 4: Running Bay 0 
WANPortLoopbackTest{ID=5} ...
Jul  5 10:36:15: %DIAG-SP-3-TEST_FAIL: Module 4: Bay 0 
WANPortLoopbackTest{ID=5} has failed. Error code = 0x1
Jul  5 10:36:15: %DIAG-SP-6-TEST_RUNNING: Module 4: Running 
TestEobcStressPing{ID=3} ...
10:31:18: SP: 
******************************************************************
10:31:18: SP: * WARNING:
10:31:18: SP: * EOBC Stress Ping test on module 4 may take up to 3min.
10:31:18: SP: * During this time, please DO NOT perform packet switching on 
the module.
10:31:18: SP: 
******************************************************************
Jul  5 10:36:33: %DIAG-SP-6-TEST_OK: Module 4: TestEobcStressPing{ID=3} has 
completed successfully

Based on the log output it looks like bay 0 & 1 failed the 
WANPortLoopbackTest but when I do:

gp1#sho diagno result module 4

Current bootup diagnostic level: complete

         Module 4:

           Overall Diagnostic Result for Module 4 : MAJOR ERROR
           Diagnostic level at card bootup: complete

           Test results: (. = Pass, F = Fail, U = Untested)

             1) TestTxPathMonitoring ------------> .
             2) BusConnectivityTest -------------> .
             3) TestEobcStressPing --------------> .
             4) Bay 1 WANPortLoopbackTest -------> F
             5) Bay 0 WANPortLoopbackTest -------> .

so I looked at the detail:

             4) Bay 1 WANPortLoopbackTest -------> F

                   Error code ------------------> 1 (DIAG_FAILURE)
                   Total run count -------------> 3
                   Last test execution time ----> Jul 05 2005 10:36:15
                   First test failure time -----> Jul 05 2005 10:36:15
                   Last test failure time ------> Jul 05 2005 10:36:15
                   Last test pass time ---------> Jul 04 2005 23:59:47
                   Total failure count ---------> 1
                   Consecutive failure count ---> 1
           ___________________________________________________________________

             5) Bay 0 WANPortLoopbackTest -------> .

                   Error code ------------------> 1 (DIAG_FAILURE)
                   Total run count -------------> 2
                   Last test execution time ----> Jul 05 2005 10:36:15
                   First test failure time -----> Jul 05 2005 10:36:15
                   Last test failure time ------> Jul 05 2005 10:36:15
                   Last test pass time ---------> Jul 04 2005 23:59:47
                   Total failure count ---------> 1
                   Consecutive failure count ---> 1

Why is it flagging Bay0 as passed when it clearly has failed?

Thanks,
Hank

PS Couldn't find anything in bugtools.