[c-nsp] Cisco blade switch config

[Kevin Berry]

I have (2) Cisco blade switches running in redundant mode and each is
connected to the same HP ROOT switch on the other end. Each blade switch
has an LACP / Etherchannel link of 2 cables going to the HP root. STP
enabled on the Cisco's.

Noticed this on my Cisco-SW1 today:

Group  Port-channel  Protocol    Ports
------+-------------+-----------+-----------------------------------------------
1      Po1(SU)         LACP      Gi0/1(I)    Gi0/2(I)    Gi0/3(I)
                                 Gi0/4(D)    Gi0/5(D)    Gi0/6(I)
                                 Gi0/7(D)    Gi0/8(I)    Gi0/20(P)
                                 Gi0/22(P)

This shows that gi 0/20 & 0/22 are in use and bundled in port channel as
they should be. My blade servers (gi 0/1 - 0/8)  (some of which are down I
know) show (I) independant? Can anyone advise why?

Also, anyone know why a server like gi 0/1 for example will not talk on
multiple vlans?
I mean, they are set correctly on the HP, as I can ping out fine to those
vlans over there. Here is the Cisco config for those vlans. Cisco talks on
VLAN 1 fine. But Vlans 2 & 3, it doesnt.

!
spanning-tree mode pvst
spanning-tree extend system-id
spanning-tree uplinkfast
no spanning-tree vlan 4-99
!
vlan internal allocation policy ascending
!
!
!
interface Port-channel1
 description HP CORE
 switchport trunk allowed vlan 1-3,100
 switchport mode trunk
 spanning-tree portfast trunk
 spanning-tree vlan 4-99 cost 20
!
!
interface GigabitEthernet0/1
 switchport trunk allowed vlan 1-3,100
 switchport mode trunk
 speed 1000
 channel-group 1 mode active
 spanning-tree portfast
!
interface GigabitEthernet0/2
 switchport trunk allowed vlan 1-3,100
 switchport mode trunk
 speed 1000
 channel-group 1 mode active
 spanning-tree portfast
interface GigabitEthernet0/20
 description HP CORE
 switchport trunk allowed vlan 1-3,100
 switchport mode trunk
 channel-protocol lacp
 channel-group 1 mode active
 spanning-tree portfast trunk
!
interface GigabitEthernet0/21
 no switchport
 no ip address
 shutdown
 spanning-tree portfast trunk
!
interface GigabitEthernet0/22
 description HP CORE
 switchport trunk allowed vlan 1-3,100
 switchport mode trunk
 channel-protocol lacp
 channel-group 1 mode active
 spanning-tree portfast trunk
!
interface GigabitEthernet0/23
 description INTERNAL CROSSCONNECT
 switchport trunk allowed vlan 1-3,100
 switchport mode trunk
 media-type internal
 channel-protocol lacp
 spanning-tree portfast trunk

interface GigabitEthernet0/24
 description INTERNAL CROSSCONNECT
 no switchport
 no ip address
 no ip route-cache
 media-type internal
 spanning-tree portfast
!
interface Vlan1
 ip address 10.10.0.18 255.255.0.0
 no ip route-cache
 no ip mroute-cache
!
interface Vlan2
 no ip address
 no ip route-cache
 no ip mroute-cache
!
interface Vlan3
 no ip address
 no ip route-cache
 no ip route-cache
--------------------------------------------------

Anyone can help?????