[cisco-voip] debug isdn q931
Ryan Ratliff
rratliff at cisco.com
Thu Jun 15 14:03:50 EDT 2006
nfas is the protocol that lets you bind multiple PRIs to the same D-
chan. Definitely not supported with MGCP though.
How about if you turn on 'deb mgcp packet' along with your q931 debug?
-Ryan
On Jun 15, 2006, at 2:02 PM, Ed Leatherman wrote:
They are definately both PRI
Isnt there some configuration that allows multiple PRI's to share a D-
channel? I specifically told the telco we didnt want this, and i'd be
surprised if it would work without any extra configuration on my
side, but thats the only other thing I could think of.
#sh isdn status
Global ISDN Switchtype = primary-4ess
%Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 1. Layer 3 output
may not apply
ISDN Serial0/0/0:23 interface
dsl 1, interface ISDN Switchtype = primary-ni
L2 Protocol = Q.921 0x0000 L3 Protocol(s) = CCM MANAGER 0x0003
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 1 CCBs = 0
The Free Channel Mask: 0x807FFFFF
Number of L2 Discards = 0, L2 Session ID = 203
Total Allocated ISDN CCBs = 0
On 6/15/06, Ryan Ratliff <rratliff at cisco.com> wrote: Are both of them
PRIs for sure? Perhaps the one not showing q931
debugs is actually a channel-group (CAS) and not a PRI?
-Ryan
On Jun 15, 2006, at 11:37 AM, Ed Leatherman wrote:
Just had the defaults on both routers, however I tried the "logging
console 7" on the problem router, which looks like it should display
debuging messages and it still shows nothing.
Just for grins and giggles I turned on debug cdp packets, and i am
getting debug messages on both routers.. so its something with the
ISDN that is causing it to not display.
On 6/15/06, Mark Borchers <mborchers at igillc.com> wrote:
Have you set your logging level high enough to show debug traffic?
See the logging console command args.
-----Original Message-----
From: cisco-voip-bounces at puck.nether.net [mailto: cisco-voip-
bounces at puck.nether.net] On Behalf Of Ed Leatherman
Sent: Thursday, June 15, 2006 10:26 AM
To: ciscovoip
Cc: jeff.davis at mail.wvu.edu
Subject: [cisco-voip] debug isdn q931
I'm fairly certain this is something I am doing wrong but I cant find
it for the life of me..
I have 2 ISR routers, 3825 with some T1 interfaces and DSPs for
conferencing. identical firmware loads and configurations, other than
1 has an FXO card that the other doesn't.
I'm executing on both routers from seperate SSH sessions:
# term mon
# debug isdn q931
On router A, I can see all the Q931 debug messages go by. On router
B, I see nothing on the SSH session however I know calls are being
placed on it ( I can see the channels going in service etc from
RTMT). Could I have something turned off on router B that doesnt show
up in the config?
--
Ed Leatherman
IP Telephony Coordinator
West Virginia University
Telecommunications and Network Operations
--
Ed Leatherman
IP Telephony Coordinator
West Virginia University
Telecommunications and Network Operations
_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
--
Ed Leatherman
IP Telephony Coordinator
West Virginia University
Telecommunications and Network Operations
More information about the cisco-voip
mailing list