[cisco-voip] Dial collection

[Ryan Ratliff]

Disabling overlap receiving will probably break the digital pbx  
phones ability to dial though :)

You can try disabling dtmf-relay on the inbound pots dial-peer but  
this may not work.

-Ryan

On Jun 20, 2006, at 11:11 AM, Fedorov, Konstantin wrote:

Hi,



The best way disable overlap send on the PBX.



But try remove

isdn overlap-receiving T302 5000



-----------------------
Sincerely Yours,
Konstantin Fedorov

From: Brian Turnbow [mailto:b.turnbow at twt.it]
Sent: Tuesday, June 20, 2006 7:02 PM
To: Fedorov, Konstantin; cisco-voip at puck.nether.net
Subject: RE: [cisco-voip] Dial collection



Hi

yes and with two state dialing , The end users digits a code to  
access the voip line and receives tone fron the router ( no direct  
dial in)

Below is an ISDN setup, and everything looks ok.

However on the outboud h323 i See  00223366552299443300 as the called  
number.

ISDN phones send correct on the pbx, it is only the analog lines that  
have this problem.





*Jun 20 14:59:16.151: ISDN Se0/0/0:15 Q931: RX <- SETUP pd = 8   
callref = 0x018E
         Bearer Capability i = 0x9090A3
                 Standard = CCITT
                 Transer Capability = 3.1kHz Audio
                 Transfer Mode = Circuit
                 Transfer Rate = 64 kbit/s
         Channel ID i = 0xA98385
                 Exclusive, Channel 5
         Progress Ind i = 0x8083 - Origination address is non-ISDN
         Calling Party Number i = 0x0181, '219'
                 Plan:ISDN, Type:Unknown
         Low Layer Compat i = 0x9090A3
*Jun 20 14:59:16.159: ISDN Se0/0/0:15 Q931: TX -> SETUP_ACK pd = 8   
callref = 0x818E
         Channel ID i = 0xA98385
                 Exclusive, Channel 5
*Jun 20 14:59:16.991: ISDN Se0/0/0:15 Q931: RX <- INFORMATION pd = 8   
callref = 0x018E
         Called Party Number i = 0x81, '0'
                 Plan:ISDN, Type:Unknown
*Jun 20 14:59:17.779: ISDN Se0/0/0:15 Q931: RX <- INFORMATION pd = 8   
callref = 0x018E
         Called Party Number i = 0x81, '2'
                 Plan:ISDN, Type:Unknown
*Jun 20 14:59:18.495: ISDN Se0/0/0:15 Q931: RX <- INFORMATION pd = 8   
callref = 0x018E
         Called Party Number i = 0x81, '3'
                 Plan:ISDN, Type:Unknown
*Jun 20 14:59:19.199: ISDN Se0/0/0:15 Q931: RX <- INFORMATION pd = 8   
callref = 0x018E
         Called Party Number i = 0x81, '6'
                 Plan:ISDN, Type:Unknown
*Jun 20 14:59:19.795: ISDN Se0/0/0:15 Q931: RX <- INFORMATION pd = 8   
callref = 0x018E
         Called Party Number i = 0x81, '5'
                 Plan:ISDN, Type:Unknown
*Jun 20 14:59:20.387: ISDN Se0/0/0:15 Q931: RX <- INFORMATION pd = 8   
callref = 0x018E
         Called Party Number i = 0x81, '2'
                 Plan:ISDN, Type:Unknown
*Jun 20 14:59:21.087: ISDN Se0/0/0:15 Q931: RX <- INFORMATION pd = 8   
callref = 0x018E
         Called Party Number i = 0x81, '9'
                 Plan:ISDN, Type:Unknown
*Jun 20 14:59:21.591: ISDN Se0/0/0:15 Q931: RX <- INFORMATION pd = 8   
callref = 0x018E
         Called Party Number i = 0x81, '4'
                 Plan:ISDN, Type:Unknown
*Jun 20 14:59:22.391: ISDN Se0/0/0:15 Q931: RX <- INFORMATION pd = 8   
callref = 0x018E
         Called Party Number i = 0x81, '3'
                 Plan:ISDN, Type:Unknown
*Jun 20 14:59:22.983: ISDN Se0/0/0:15 Q931: RX <- INFORMATION pd = 8   
callref = 0x018E
         Called Party Number i = 0x81, '0'
                 Plan:ISDN, Type:Unknown
*Jun 20 14:59:27.987: ISDN Se0/0/0:15 Q931: TX -> CALL_PROC pd = 8   
callref = 0x818E

interface Serial0/0/0:15
  no ip address
  isdn switch-type primary-net5
  isdn overlap-receiving T302 5000
  isdn network-failure-cause 16
  isdn protocol-emulate network
  isdn incoming-voice voice
  isdn send-alerting
  no cdp enable







thanks

Brian



From: Fedorov, Konstantin [mailto:kfedor at amt.ru]
Sent: martedì 20 giugno 2006 16.54
To: Brian Turnbow; cisco-voip at puck.nether.net
Subject: RE: [cisco-voip] Dial collection

Hi, Brian.



ISDN Info – so you PBX send digits over overlap.



Whai is you scenario ? Two state dialing ??



Can you send a snip  of

Debug isdn q931



And D channel configuration.

-----------------------
Sincerely Yours,
Konstantin Fedorov

From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip- 
bounces at puck.nether.net] On Behalf Of Brian Turnbow
Sent: Tuesday, June 20, 2006 6:45 PM
To: cisco-voip at puck.nether.net
Subject: [cisco-voip] Dial collection





Hello all,

I have a 2821 with a E1 multiflex card connected to a PBX.
When analog lines of the pbx dial out I receive both the in band  
dialed digits and isdn info messages from the pbx.
This causes the router to send out in h323 the incorrect numer . For  
example  1234 gets sent out as 11223344
I have been looking for a way to disable the in band digit  
collection, but have yet to find out how.
Can any one point me in the right direction ?

Thanks
Brian

_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip