[cisco-voip] Berbee, multicast etc..

[Chris Baird]

Some things to look at:

- confirm with berbee if there is a certain multicast mode ex. PIM
Sparse-Dense that needs to be running
- has paging ever worked across the WAN?
- if so, what has changed
- will the paging only work on certain phones across the WAN?
- sniff the multicast address that berbee uses/place an IP phone at each
interface across the WAN and attempt a page
- berbee may require phones to be associated to a particular CTI user in
Call Manager; if so has this been done?

Good luck,
Chris


-----Original Message-----
From: cisco-voip-bounces at puck.nether.net
[mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Andrew Dignan
Sent: Sunday, March 05, 2006 6:39 PM
To: cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] Berbee, multicast etc..

Immediately after you send a page to the IP Phone at the remote site, can
you paste in the output of a "show ip mroute" from the local router AND
the remote router?

Andy Dignan
berbee

> I don't think so.. The router on the Frame side has the multicast route.
> and if I page from theberbee server local side it works..
> Only when paging from the berbee server remote frame location side does
> it not pass the voice part of the page....
>
> Jim
>
> ________________________________
>
> From: Ortiz, Carlos [mailto:CORTIZ at broward.org]
> Sent: Saturday, March 04, 2006 2:36 PM
> To: Jim McBurnett; cisco-voip at puck.nether.net
> Subject: RE: [cisco-voip] Berbee, multicast etc..
>
>
> I use the IPcelerate paging and do know that you need to make sure that
> the multicast TTL is set high enough allow the page to get to the
> subnet.  Could that be an issue?
>
> Carlos
>
> ________________________________
>
> From: cisco-voip-bounces at puck.nether.net on behalf of Jim McBurnett
> Sent: Sat 3/4/2006 12:17 PM
> To: cisco-voip at puck.nether.net
> Subject: [cisco-voip] Berbee, multicast etc..
>
>
>
> I know there is a Berbee list, but I have a question..
>
> If Berbee can send a page from a phone in the same subnet the Berbee
> server is sitting in but can't send that page to a remote routed segment
> when the Phone in the remote segment initiates the page.  What could the
> cause be?
>
> Situation 1:
>         Phone IP a.b.c.200
>         Berbee server a.b.c.102
>         Phone initiates a page and it pages and live audio comes out on
> phones on a routed Frame site on w.x.y.z /24 segment
>
>
> Situation 2:
>         Phone IP w.x.y.30
>         Berbee Server a.b.c.102
>         Phone initiates a page and all the berbee tones come out on the
> speakers at w.x.y.z location.
>                 BUT live audio paging does not.
>
> All routers are displaying the multicast route to the berbee server.
>
> Ideas anyone?
>
> Jim
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>

_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip