[cisco-voip] SIP Trunk -> PSTN
Robin Inderberg
robin.inderberg at candidator.se
Wed Mar 15 07:57:55 EST 2006
Hi there Fedorov,
i found out that too, and I have not configured a MTP on the CCM cluster.
I will do that now, and se how it works.
Thank you for you answer!
Med vänliga hälsningar/Best regards
Robin Inderberg
robin.inderberg at candidator.se <mailto:robin.inderberg at candidator.se>
_____________________________________________
Telefon: 0322-67 10 00 www.candidator.se <http://www.candidator.se/>
Direkt: 0322-67 10 19 Candidator AB
Mobil: 0733-47 10 19 Malmgatan 15
Fax: 0322-67 10 99 441 39 ALINGSÅS
¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯
________________________________
From: Fedorov, Konstantin [mailto:kfedor at amt.ru]
Sent: den 15 mars 2006 11:27
To: Robin Inderberg; cisco-voip at puck.nether.net
Subject: RE: [cisco-voip] SIP Trunk -> PSTN
Hi,
Sip Trunk can open RTP only with g711 codec A or u law.
So you must use transcoder for this call.
In the SIP trunk configuration, select " Use mtp"
-----------------------
Sincerely Yours,
Konstantin Fedorov
________________________________
From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Robin Inderberg
Sent: Wednesday, March 15, 2006 1:24 PM
To: cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] SIP Trunk -> PSTN
Hi once again,
Some more information regarding this problem.
The region I use on all devices here has the codec G729 configured.
a=rtpmap:18 G729/8000
a=fmtp:18 annexb=yes
a=rtpmap:8 PCMA/8000
a=rtpmap:0 PCMU/8000
a=rtpmap:100 X-NSE/8000
a=fmtp:100 192-194
as the telcos debug says they have G729 as prio 1.
I enabled detailed bugging on the CCM now, and got the following errors.
This is for an incomming call, where the phone is ringing, and then it is answered.
03/15/2006 10:48:51.029 CCM|MtpNoMoreResourcesAvailable - No more MTP resources available. App ID:Cisco CallManager Cluster ID:StandAloneCluster Node ID:10.1.10.51|<CLID::StandAloneCluster><NID::10.1.10.51><CT::Alarm>
03/15/2006 10:48:51.029 CCM|MRM::waiting_AllocateMtpResourceErr - ERROR - no resources are available -- ci = 16777269|<CLID::StandAloneCluster><NID::10.1.10.51><CT::1,100,119,1.652><IP::10.1.10.101><DEV::SEP0016462CFEED>
03/15/2006 10:48:51.029 CCM|MediaManager(3) - ERROR disconnOnResourceAllocationFailure - fails to allocate MTP/XCoder,connCount=2|<CLID::StandAloneCluster><NID::10.1.10.51><CT::1,100,119,1.652><IP::10.1.10.101><DEV::SEP0016462CFEED>
03/15/2006 10:48:51.029 CCM|MRM::waiting_DeallocateMtpResourceReq- ERROR Deallocate received for an unknown Call Identifier Ci = 16777269|<CLID::StandAloneCluster><NID::10.1.10.51><CT::1,100,119,1.652><IP::10.1.10.101><DEV::SEP0016462CFEED>
03/15/2006 10:48:51.029 CCM|ConnectionManager - wait_AuDisconnectRequest:NO ENTRY FOUND IN TABLE,CI(16777267,16777268),dcType=1,IFCreated(0,0),PID(0-0,0-0),IFHandling(0,0),MCNode(0,0)|<CLID::StandAloneCluster><NID::10.1.10.51><CT::1,100,119,1.652><IP::10.1.10.101><DEV::SEP0016462CFEED>
Here is the output for an outgoing call, that didn't make its way through.
03/15/2006 10:50:55.064 CCM|MtpNoMoreResourcesAvailable - No more MTP resources available. App ID:Cisco CallManager Cluster ID:StandAloneCluster Node ID:10.1.10.51|<CLID::StandAloneCluster><NID::10.1.10.51><CT::Alarm>
03/15/2006 10:50:55.064 CCM|MRM::waiting_AllocateMtpResourceErr - ERROR - no resources are available -- ci = -2130706352|<CLID::StandAloneCluster><NID::10.1.10.51><CT::1,100,119,1.671><IP::10.1.10.101><DEV::SEP0016462CFEED>
03/15/2006 10:50:55.064 CCM|MtpNoMoreResourcesAvailable - No more MTP resources available. App ID:Cisco CallManager Cluster ID:StandAloneCluster Node ID:10.1.10.51|<CLID::StandAloneCluster><NID::10.1.10.51><CT::Alarm>
03/15/2006 10:50:55.064 CCM|MRM::waiting_AllocateMtpResourceErr - ERROR - no resources are available -- ci = -2130706352|<CLID::StandAloneCluster><NID::10.1.10.51><CT::1,100,119,1.671><IP::10.1.10.101><DEV::SEP0016462CFEED>
03/15/2006 10:50:55.064 CCM|ConnectionManager - wait_AuDisconnectRequest:NO ENTRY FOUND IN TABLE,CI(16777270,0),dcType=1,IFCreated(0,0),PID(0-0,0-0),IFHandling(0,0),MCNode(0,0)|<CLID::StandAloneCluster><NID::10.1.10.51><CT::1,100,119,1.671><IP::10.1.10.101><DEV::SEP0016462CFEED>
Someone who have any idéas?
Med vänliga hälsningar/Best regards
Robin Inderberg
robin.inderberg at candidator.se <mailto:robin.inderberg at candidator.se>
_____________________________________________
Telefon: 0322-67 10 00 www.candidator.se <http://www.candidator.se/>
Direkt: 0322-67 10 19 Candidator AB
Mobil: 0733-47 10 19 Malmgatan 15
Fax: 0322-67 10 99 441 39 ALINGSÅS
¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯
________________________________
From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Robin Inderberg
Sent: den 15 mars 2006 09:03
To: cisco-voip at puck.nether.net
Subject: [cisco-voip] SIP Trunk -> PSTN
Good morning everyone,
Time for a new question.
I got a CCM 4.1(3)sr3a that will use a SIP Trunk to my telco.
I have got the incomming calls to work, so far as I get the ringing here.
If I answer the call, the call is teared down.
I have ran debug sip on my pix I got here.
Here it comes,
1498: NAT::table route: embedded host at outside:XXX.XXX.190.42/5060
1499: NAT::pre-allocate connection for outside:XXX.XXX.190.42 to outside:XXX.XXX.190.42/5060
1500: NAT::no connection necessary, same security level
1501: SIP::Response 5xx received from inside:10.1.10.51/5060 to outside:XXX.XXX.190.42/5060
1502: SIP::Found From addr "sip:0733471019 at XXX.XXX.198.110" (30)
1503: SIP::Found To addr "sip:0322640000 at my-sip-telco-host" (37)
1504: SIP::Found Call-ID 70AA62A2-B32E11DA-BF8094C9-5F478392 at XXX.XXX.198.110 (51)
1505: SIP::Found CSeq 101 INVITE
Found port 5060
1506: SIP::Embedded IP XXX.XXX.190.42/5060
1507: NAT::NAT UDP XXX.XXX.190.42/5060
from inside:10.1.10.51/5060 to outside:XXX.XXX.190.42/5060
1508: NAT::table route: embedded host at outside:XXX.XXX.190.42/5060
1509: NAT::find/create NAT rule for outside:XXX.XXX.190.42/5060 to outside:XXX.XXX.190.42
1510: NAT::receiver and embedded hosts on same interface
1511: NAT::embedded socket translates to outside:XXX.XXX.190.42/5060
Found port 5060
1512: SIP::Embedded IP XXX.XXX.198.110/5060
1513: NAT::NAT UDP XXX.XXX.198.110/5060
from inside:10.1.10.51/5060 to outside:XXX.XXX.190.42/5060
1514: NAT::table route: embedded host at outside:XXX.XXX.198.110/5060
1515: NAT::find/create NAT rule for outside:XXX.XXX.198.110/5060 to outside:XXX.XXX.190.42
1516: NAT::receiver and embedded hosts on same interface
1517: NAT::embedded socket translates to outside:XXX.XXX.198.110/5060
1518: SIP::Embedded IP XXX.XXX.198.110/0
1519: NAT::NAT UDP XXX.XXX.198.110/0
from inside:10.1.10.51/5060 to outside:XXX.XXX.190.42/5060
1520: NAT::table route: embedded host at outside:XXX.XXX.198.110/0
1521: NAT::find/create NAT rule for outside:XXX.XXX.198.110/0 to outside:XXX.XXX.190.42
1522: NAT::receiver and embedded hosts on same interface
1523: NAT::embedded socket translates to outside:XXX.XXX.198.110/0
1524: SIP::Embedded IP XXX.XXX.198.110/0
1525: NAT::NAT UDP XXX.XXX.198.110/0
from inside:10.1.10.51/5060 to outside:XXX.XXX.190.42/5060
1526: NAT::table route: embedded host at outside:XXX.XXX.198.110/0
1527: NAT::find/create NAT rule for outside:XXX.XXX.198.110/0 to outside:XXX.XXX.190.42
1528: NAT::receiver and embedded hosts on same interface
1529: NAT::embedded socket translates to outside:XXX.XXX.198.110/0
1530: SIP::Embedded IP 10.1.10.51/0
1531: NAT::NAT UDP 10.1.10.51/0
from inside:10.1.10.51/5060 to outside:XXX.XXX.190.42/5060
1532: NAT::reverse route: embedded host at inside:10.1.10.51/0
1533: NAT::find/create NAT rule for inside:10.1.10.51/0 to outside:XXX.XXX.190.42
1534: NAT::inside NAT with current xlate
1535: NAT::embedded socket translates to outside:XXX.XXX.XXX.66/0
1536: SIP::Deleting session for 10.1.10.51 to XXX.XXX.190.42, 0 total
From: sip:0733471019 at XXX.XXX.198.110 (30)
To: sip:0322640000 at my-sip-telco-host (37)
Call-ID: 70AA62A2-B32E11DA-BF8094C9-5F478392 at XXX.XXX.198.110 (51)
CSeq: 101 INVITE
1537: SIP::ACK received from outside:XXX.XXX.190.42/5060 to inside:10.1.10.51/0
Found port 5060
1538: SIP::Embedded IP XXX.XXX.XXX.66/5060
1539: NAT::NAT UDP XXX.XXX.XXX.66/5060
from outside:XXX.XXX.190.42/5060 to inside:10.1.10.51/5060
1540: NAT::xlate route: embedded host at inside:10.1.10.51/5060
1541: NAT::find/create NAT rule for inside:10.1.10.51/5060 to inside:10.1.10.51
1542: NAT::receiver and embedded hosts on same interface
1543: NAT::embedded socket translates to inside:10.1.10.51/5060
1544: SIP::Embedded IP XXX.XXX.190.42/0
1545: NAT::NAT UDP XXX.XXX.190.42/0
from outside:XXX.XXX.190.42/5060 to inside:10.1.10.51/5060
1546: NAT::reverse route: embedded host at outside:XXX.XXX.190.42/0
1547: NAT::find/create NAT rule for outside:XXX.XXX.190.42/0 to inside:10.1.10.51
1548: NAT::outside NAT with current xlate
1549: NAT::embedded socket translates to inside:XXX.XXX.190.42/0
1550: SIP::Embedded IP XXX.XXX.198.110/0
1551: NAT::NAT UDP XXX.XXX.198.110/0
from outside:XXX.XXX.190.42/5060 to inside:10.1.10.51/5060
1552: NAT::table route: embedded host at outside:XXX.XXX.198.110/0
1553: NAT::find/create NAT rule for outside:XXX.XXX.198.110/0 to inside:10.1.10.51
1554: NAT::outside NAT not needed
1555: NAT::embedded socket translates to inside:XXX.XXX.198.110/0
1556: SIP::Embedded IP XXX.XXX.198.110/0
1557: NAT::NAT UDP XXX.XXX.198.110/0
from outside:XXX.XXX.190.42/5060 to inside:10.1.10.51/5060
1558: NAT::table route: embedded host at outside:XXX.XXX.198.110/0
1559: NAT::find/create NAT rule for outside:XXX.XXX.198.110/0 to inside:10.1.10.51
1560: NAT::outside NAT not needed
1561: NAT::embedded socket translates to inside:XXX.XXX.198.110/0
1562: SIP::Found From addr "sip:0733471019 at XXX.XXX.198.110" (30)
1563: SIP::Found Call-ID 70AA62A2-B32E11DA-BF8094C9-5F478392 at XXX.XXX.198.110 (51)
1564: SIP::Found To addr "sip:0322640000 at my-sip-telco-host" (37)
1565: SIP::Found CSeq 101 ACK
1566: Created SIP session for 10.1.10.51/0 to XXX.XXX.190.42/5060, 1 total
From: sip:0733471019 at XXX.XXX.198.110 (30)
To: sip:0322640000 at my-sip-telco-host (37)
Call-ID: 70AA62A2-B32E11DA-BF8094C9-5F478392 at XXX.XXX.198.110 (51)
CSeq: 101 ACK
1567: NAT::requesting UDP conn for XXX.XXX.190.42/0 [0.0.0.0/0]
from outside:XXX.XXX.190.42/5060 to inside:10.1.10.51/5060
1568: NAT::ERROR: invalid sockets: <third>:XXX.XXX.190.42/0 <fourth>:0.0.0.0/0
Anyone who has any idéa?
The network looks something like this, CCM 10.1.10.51 -> 2950T -> 10.1.10.61 PIX 501 XXX.XXX.XXX.66 -> ISP INT VPN -> XXX.XXX.19X.XXX TELCO SIP
Med vänliga hälsningar/Best regards
Robin Inderberg
robin.inderberg at candidator.se <mailto:robin.inderberg at candidator.se>
_____________________________________________
Telefon: 0322-67 10 00 www.candidator.se <http://www.candidator.se/>
Direkt: 0322-67 10 19 Candidator AB
Mobil: 0733-47 10 19 Malmgatan 15
Fax: 0322-67 10 99 441 39 ALINGSÅS
¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯
-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://puck.nether.net/pipermail/cisco-voip/attachments/20060315/2d89fb04/attachment-0001.html
More information about the cisco-voip
mailing list