[cisco-voip] 2801 MGCP Gateway on CCM 5.0

[alsvrj]

Hello All, 

I have an 2801 connected to a Hicom 330 PBX through a ISDN PRI QSIG with 
MGCP and a CCM5.0. I´m having a lot of problems to get the gateway 
registration on CCM. 

I would like to do some questions: 
1- Is it possible to put an ISDN PRI with MGCP using QSIG signaling ? 

Using the show isdn status command I´m seeing MULTIPLE_FRAME_ESTABILISHED 

I´m seeing too with the show ccm-manager that the MGCP is Active but I´m not 
able to see this Gateway into the active state inside of CCM. 

I´m using a VWIC-1MFT-E1 card to use this ISDN PRI. 

2- Is it possible to put the IP Address instead of Domain Name when I´m 
creating the 2801 Gateway ? 

Hey guys, I really need your help to solve this registration problem, I 
kindly ask a hand into this situation. 

Thanks for everything. 

It follows below the configuration on the Gateway: 

hostname GW2801 
! 
boot-start-marker 
boot system flash c2801-adventerprisek9-mz.124-6.T3.bin 
boot-end-marker 
! 
logging buffered 4096 informational 
enable secret 5 ******************** 
! 
no aaa new-model 
! 
resource policy 
! 
clock timezone UTC -3 
network-clock-participate wic 2 
network-clock-select 1 E1 0/2/0 
ip cef 
! 
! 
! 
! 
ip tcp synwait-time 13 
no ip domain lookup 
ip domain name test.br 
ip name-server *.*.*.* 
ip name-server *.*.*.* 
ip name-server *.*.*.* 
! 
isdn switch-type primary-qsig 
isdn logging 
! 
voice-card 0 
 dsp services dspfarm 
! 
! 
voice call carrier capacity active 
! 
! 
voice class codec 1 
 codec preference 1 g711ulaw 
 codec preference 2 g729r8 bytes 40 
! 
! 
! 
voice class h323 1 
 h225 timeout tcp establish 3 
! 
crypto configuration 
! 
controller E1 0/2/0 
 framing NO-CRC4 
 line-termination 75-ohm 
 pri-group timeslots 1-31 service mgcp 
! 
! 
interface FastEthernet0/0 
 ip address *.*.*.* *.*.*.* 
 speed 100 
 full-duplex 
 no cdp enable 
 h323-gateway voip bind srcaddr *.*.*.* 
! 
interface FastEthernet0/1 
 no ip address 
 shutdown 
 duplex auto 
 speed auto 
 no cdp enable 
! 
interface Serial0/1/0 
 no ip address 
 shutdown 
 clock rate 2000000 
 no cdp enable 
! 
interface Serial0/2/0:15 
 no ip address 
 no ip proxy-arp 
 encapsulation hdlc 
 isdn switch-type primary-qsig 
 isdn overlap-receiving 
 isdn incoming-voice voice 
 isdn supp-service name calling 
 isdn bind-l3 ccm-manager 
 isdn negotiate-bchan 
 isdn bchan-number-order ascending 
 isdn sending-complete 
 no cdp enable 
! 
ip route 0.0.0.0 0.0.0.0 *.*.*.* 
! 
! 
ip http server 
ip http secure-server 
! 
logging *.*.*.* 
access-list 1 permit *.*.*.* 
access-list 1 permit *.*.*.* 
dialer-list 1 protocol ip permit 
snmp-server community voip RW 1 
snmp-server community ext0399 RW 1 
snmp-server community sw0399 RW 1 
disable-eadi 
no cdp run 
! 
control-plane 
! 
voice-port 0/2/0:15 
! 
ccm-manager mgcp 
ccm-manager music-on-hold 
ccm-manager config server *.*.*.* 
ccm-manager config 
! 
mgcp 
mgcp call-agent *.*.*.* 2427 service-type mgcp version 0.1 
mgcp dtmf-relay voip codec all mode out-of-band 
mgcp rtp unreachable timeout 1000 action notify 
mgcp modem passthrough voip mode nse 
mgcp package-capability rtp-package 
no mgcp package-capability res-package 
mgcp package-capability sst-package 
no mgcp package-capability fxr-package 
mgcp package-capability pre-package 
no mgcp timer receive-rtcp 
mgcp sdp simple 
mgcp fax t38 inhibit 
mgcp rtp payload-type g726r16 static 
! 
mgcp profile default 
! 
! 
dial-peer cor custom 
! 
! 
! 
dial-peer voice 1 pots 
 service mgcpapp 
 port 0/2/0:15 
! 
! 
! 
line con 0 
 exec-timeout 0 0 
 password 7 ***************** 
 logging synchronous 
 login 
line aux 0 
 exec-timeout 0 0 
 password 7 ***************** 
 logging synchronous 
 login 
line vty 0 4 
 exec-timeout 0 0 
 password 7 ************** 
 logging synchronous 
 login 
! 
scheduler allocate 20000 1000 
ntp clock-period 17180079 
ntp server *.*.*.* 
! 
webvpn context Default_context 
 ssl authenticate verify all 
 ! 
 no inservice 
end