[cisco-voip] Local call send out from SRST gatewayr when not inSRST mode

Sat Jul 21 00:05:53 EDT 2007

Lelio,
Thank you very much for your reply, Do you mean register branch office
SRST gateway on call manager as a second voice gateway? if so, do I
need any special settings on SRST ?
Bellow is my current SRST configuration.

Regards,
Manoj

!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname TEST01
!
boot-start-marker
boot-end-marker
!
enable password xxxxxxxxx
!
aaa new-model
!
!
aaa authentication login userauth local
!
!
aaa session-id common
clock timezone jst 9
network-clock-participate wic 0
ip cef
!
!
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.9.200 192.168.9.254
ip dhcp excluded-address 192.168.9.1 192.168.9.99
ip dhcp excluded-address 192.168.7.151 192.168.7.254
ip dhcp excluded-address 192.168.7.1 192.168.7.99
!
ip dhcp pool DATA
   network 192.168.9.0 255.255.255.0
   default-router 192.168.9.1
   dns-server 61.122.112.97
   lease 14
!
ip dhcp pool VOICE
   network 192.168.7.0 255.255.255.0
   domain-name write
   dns-server 172.16.0.10
   default-router 192.168.7.1
   option 150 ip 172.16.0.10
   lease 14
!
!
ip domain name xxx.com
!
multilink bundle-name authenticated
!
isdn switch-type ntt
!
voice-card 0
!
!
!
voice translation-rule 1
 rule 1 /1602/ /0335119981/
 rule 2 /1607/ /0335119982/
 rule 3 /1609/ /0335119983/
!
voice translation-rule 2
 rule 1 /35119981/ /1602/
 rule 2 /35119982/ /1607/
 rule 3 /35119983/ /1609/
!
!
voice translation-profile ANI
 translate calling 1
!
voice translation-profile DNIS
 translate called 2
!
!
!
policy-map AutoQoS-Policy-Trust
 class class-default
  fair-queue
policy-map Shape-20MB
 class class-default
  shape average 20000000
  service-policy AutoQoS-Policy-Trust
!
!
crypto isakmp policy 10
 encr 3des
 hash md5
 authentication pre-share
 group 2
crypto isakmp key 6 xxxxxx address 210.210.210.210 no-xauth
!
!
crypto ipsec transform-set KAM esp-3des esp-md5-hmac
!
crypto ipsec profile GREPRO
 set transform-set KAM
!
!
interface Tunnel0
 description ******* Tunnel to Main Office *********
 bandwidth 2000
 ip address 10.0.22.2 255.255.255.0
 ip nbar protocol-discovery
 tunnel source FastEthernet0/1
 tunnel destination 210.81.12.194
 tunnel mode ipsec ipv4
 tunnel protection ipsec profile GREPRO
 service-policy output Shape-20MB
!
interface FastEthernet0/0
 no ip address
 ip nat inside
 no ip virtual-reassembly
 duplex auto
 speed auto
!
interface FastEthernet0/0.10
 encapsulation dot1Q 10 native
 ip address 192.168.9.1 255.255.255.0
 ip nat inside
 ip virtual-reassembly
 ip tcp adjust-mss 1400
!
interface FastEthernet0/0.20
 encapsulation dot1Q 20
 ip address 192.168.7.1 255.255.255.0
 ip nat inside
 ip virtual-reassembly
 ip tcp adjust-mss 1400
!
interface FastEthernet0/1
 description ****** INTERNET **********
 bandwidth 2000
 ip address 124.124.124.124 255.255.255.248
 ip nat outside
 no ip virtual-reassembly
 ip route-cache flow
 ip tcp adjust-mss 1400
 speed 100
 full-duplex
!
interface BRI0/0/0
 no ip address
 isdn switch-type ntt
 isdn point-to-point-setup
 isdn incoming-voice voice
 isdn map address .* plan unknown type unknown
!
interface BRI0/0/1
 no ip address
 isdn switch-type ntt
 isdn point-to-point-setup
 isdn incoming-voice voice
 isdn map address .* plan unknown type unknown
!
interface Dialer0
 no ip address
!
ip route 0.0.0.0 0.0.0.0 124.39.174.233
ip route 10.0.0.0 255.255.255.0 Tunnel0
ip route 172.20.0.0 255.255.0.0 Tunnel0
!
!
ip http server
no ip http secure-server
ip nat inside source list 102 interface FastEthernet0/1 overload
!
access-list 102 permit ip 192.168.7.0 0.0.0.255 any
access-list 102 permit ip 192.168.9.0 0.0.0.255 any
!
!!
control-plane
!
!
!
voice-port 0/0/0
!
voice-port 0/0/1
!
!
!
dial-peer voice 1 pots
 destination-pattern 0110
 port 0/0/0
 forward-digits 3
!
dial-peer voice 2 pots
 destination-pattern 0T
 port 0/0/0
!
dial-peer voice 3 pots
 incoming called-number .
 direct-inward-dial
 port 0/0/0
!
!
!
!
call-manager-fallback
 secondary-dialtone 0
 max-conferences 8 gain -6
 transfer-system full-consult
 timeouts interdigit 3
 ip source-address 192.168.7.1 port 2000
 max-ephones 24
 max-dn 48
 voicemail 00345501603
 moh music-on-hold.au
 time-format 24
!
!
line con 0
line aux 0
line vty 0 4
 transport input telnet ssh
!
scheduler allocate 20000 1000
ntp clock-period 17178208
ntp update-calendar
ntp server 202.202.202.222 prefer
end

On 7/21/07, Lelio Fulgenzi <lelio at uoguelph.ca> wrote:
> Simply register the local ISDN BRI as a gateway (h323, mgcp, whatever) and
> create route patterns accordingly to send calls out that gateway.
>
> Basically do the same thing you did for your main office route
> patterns/gateways - just copy it for the branch office gateways.
>
>
> ----- Original Message -----
> From: "Manoj Kalpage" <manoj.kalpage at gmail.com>
> To: <cisco-voip at puck.nether.net>
> Sent: Friday, July 20, 2007 10:52 PM
> Subject: [cisco-voip] Local call send out from SRST gatewayr when not inSRST
> mode
>
>
> > HI all,
> > We have CM hosted in main office and branch office use SRST gateway
> > with local ISDN BRI voice lines (Currently ISDN BRI only use when WAN
> > fails) . Branch office located far away from main office. When branch
> > office make call to their local area numbers, it still go out to PSTN
> > from main office voice gateway so, local call for branch office
> > becomes long distance call. I am looking for solution which I can send
> > branch office local call out from SRST router using it's own ISDN BRI
> > without send them to main office voice gateway. Is this possible to do
> > with SRST or CME? any comments would be greatly appreciated.
> >
> > Best regards,
> > PERE
> > _______________________________________________
> > cisco-voip mailing list
> > cisco-voip at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-voip
> >
>
>