[cisco-voip] Ответ: 7911 factory default reset

[Daniel A. Abelski]

its the load file

Here http://www.cisco.com/en/US/products/sw/voicesw/ps4625/prod_installation_guide09186a00807aae21.html

it is said:

 When configuring the load command for  Java-based IP phones, such as
the Cisco Unified IP Phone 7906G, 7911G, 7941G, 7941GE, 7961G, 7961GE,
7970G, and 7971G, configure only the filenames that are marked with an
asterisk (*) in the table below.

and here for different ver. of firmware.	

SCCP11.7-2-1-0S.loads*
term06.default.loads term11.default.loads
cvm11.7-2-0-66.sbn
jar11.7-2-0-66.sbn
dsp11.1-0-0-73.sbn
apps11.1-0-0-72.sbn
cnu11.3-0-0-81.sbn
	

SCCP11.8-0-3S.loads*
term06.default.loads
term11.default.loads
cvm11sccp.8-0-2-25.sbn
jar11sccp.8-0-2-25.sbn
dsp11.1-1-2-26.sbn
apps11.1-1-2-26.sbn
cnu11.3-1-2-26.sbn
	

SIP11.8-2-1S.loads*
term06.default.loads
term11.default.loads
apps11.8-0-2-55.sbn
cnu11.8-2-0-55.sbn
cvm11sip.8-2-0-55.sbn
dsp11.8-2-0-55.sbn
jar11sip.8-0-2-25.sbn

So. You need the SIP11.8-2-1S.loads file and you should add to config

load 7906 SCCP11.7-2-1-0S     for example

2007/5/27, keli at carocomp.ro <keli at carocomp.ro>:
> In the mean time, this sort-of turned out to be the problem.
>
> The phone is connected to a CCME, and the router did not have the
> proper firmware files loaded. Once I did that, this phone recovered.
>
> However, since I uploaded a newer firmware, that what was on the
> phones, I restarted all the phones, and now I have a different phone
> going crazy.
>
> It can access the tftp server, it can download all the firmware files,
> but then it just keeps rebooting, with "Resetting..." appearing once
> in a while on the phone. It has this loop, where it's powering up once
> with a checkmark, once with an X in that lower-left corner of the
> screen and keeps rebooting continuously.
>
> It has power, it gets DHCP, it's in the proper VLAN, the PC after it
> is working ok etc ...
>
> In the CCME telephony-service config, what is the proper filename for
> load 7911 ????
> since I've seen various configs on the net, some claiming the jar
> file, some the SCCP and even some the apps file. Does anybody know for
> sure?
>
> thanks,
>    Zoltan
>
> Quoting Paul Choi <asobihoudai at yahoo.com>:
>
> > Can your phone talk to the tftp server properly?
> >
> >
> > --- keli at carocomp.ro wrote:
> >
> >> Hi!
> >>
> >> I have a 7911G phone, with POE, that had problems
> >> starting up - got
> >> stock in the DHCP phase. It seemd like bad cabling,
> >> but it behaved the
> >> same plugged directly into the switch (Cisco POE
> >> switch).
> >>
> >> So I tried a factory reset, but it won't recover.
> >> I'm not sure wether
> >> I completed the procedure correctly though:
> >>   - reset the phone with the # pressed
> >>   - then press 123456789*#0 in sequence
> >>
> >> The prone now enters the "Upgrading" phase, reboots,
> >> with a circle
> >> icon (bullet?) in the lower left corner (where
> >> normally a checked
> >> checkbox resides) then it begins the upgradeing
> >> proces all over again.
> >>
> >> In the mean time, it recieves an IP adress from DHCP
> >> and can be pinged
> >> for a shor while.
> >>
> >> How do I exit this loop?
> >>
> >> thanks,
> >>    Zoltan
> >>
> >
> >
> >
> >
> >
> ____________________________________________________________________________________
> > Don't pick lemons.
> > See all the new 2007 cars at Yahoo! Autos.
> > http://autos.yahoo.com/new_cars.html
> >
>
>
>
> ----------------------------------------------------------------
> This message was sent using IMP, the Internet Messaging Program.
>
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>


-- 
Regards,                    |        С Уважением,
Daniel A. Abelski        |        Абельский Даниил Александрович