[cisco-voip] CME on 2811

[Lemon]

Hi,

Got a 2811 running 12.4.15.T5 and CME 4.1 with BRI's. yesterday we
tried moving away from CME to make this a H323 gateway on CUCM. That
did not go so well so we reverted back.......only to discover that we
were seeing the same problem again.

Somehow the BRI;s are just not coming up, they show layer 1 active and
layer 2 TEI_Assigned. When trying to dial in we see the BRI layer2
come up, shows Multiple framed established but then get the following
error:

"requested circuit/channel unavailable"

Telco say they test the BRi's fine and TAC says config is correct.
Below some debug from isdn q931:


Aug 11 22:36:09.843: ISDN BR0/2/0 Q931: SETUP pd = 8  callref = 0x69
        Sending Complete
        Bearer Capability i = 0x8090A3
                Standard = CCITT
                Transfer Capability = Speech
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0x89
                Exclusive, B1
        Progress Ind i = 0x8583 - Origination address is non-ISDN
        Calling Party Number i = 0x2183, '17164000'
                Plan:ISDN, Type:National
        Called Party Number i = 0x81, '4391'
                Plan:ISDN, Type:Unknown
Aug 11 22:36:09.847: ISDN BR0/2/0 Q921: L2_EstablishDataLink: sending
SABME Aug 11 22:36:09.847: ISDN BR0/2/0 Q921: User TX -> SABMEp sapi=0
tei=88 Aug 11 22:36:09.859: ISDN BR0/2/0 Q921: User RX <- UAf sapi=0
tei=88 Aug 11 22:36:09: %ISDN-6-LAYER2UP: Layer 2 for Interface
BR0/2/0, TEI 88 changed to up Cork_CCME(config-if)# Aug 11
22:36:09.863: ISDN BR0/2/0 Q921: User TX -> INFO sapi=0 tei=88, ns=0
nr=0 Aug 11 22:36:09.863: ISDN BR0/2/0 Q931: RELEASE_COMP pd = 8
callref = 0xE9
        CAUSE I = 0X80AC - REQUESTED CIRCUIT/CHANNEL NOT AVAILABLE Aug
11 22:36:09.867: ISDN BR0/2/0 Q921: User RX <- UAf sapi=0 tei=86 Aug
11 22:36:09.871: ISDN BR0/2/0 Q921: User RX <- UAf sapi=0 tei=87 Aug
11 22:36:09.891: ISDN BR0/2/0 Q921: User RX <- RR sapi=0 tei=86 nr=1
Aug 11 22:36:09.899: ISDN BR0/2/0 Q921: User RX <- RR sapi=0 tei=87
nr=1 Aug 11 22:36:10.859: ISDN BR0/2/0 Q921: S7_T200_EXPIRY: VA = 0,
VS = 1 Aug 11 22:36:10.859: ISDN BR0/2/0 Q921: User TX -> INFOp sapi=0
tei=88, ns=0 nr=0 Cork_CCME(config-if)# Aug 11 22:36:10.859: ISDN
BR0/2/0 Q931: RELEASE_COMP pd = 8  callref = 0xE9
        Cause i = 0x80AC - Requested circuit/channel not available Aug
11 22:36:10.875: ISDN BR0/2/0 Q921: User RX <- RRf sapi=0 tei=88 nr=1
Cork_CCME(config-if)# Aug 11 22:36:19.891: ISDN BR0/2/0 Q921: User RX
<- RRf sapi=0 tei=87 nr=1 Aug 11 22:36:19.895: ISDN BR0/2/0 Q921: User
RX <- RRp sapi=0 tei=86 nr=1 Aug 11 22:36:19.899: ISDN BR0/2/0 Q921:
User RX <- RRf sapi=0 tei=86 nr=1 Aug 11 22:36:20.875: ISDN BR0/2/0
Q921: User TX -> RRp sapi=0 tei=88 nr=0 Aug 11 22:36:20.875: ISDN
BR0/2/0 Q921: User RX <- RRp sapi=0 tei=88 nr=1 Aug 11 22:36:20.879:
ISDN BR0/2/0 Q921: User TX -> RRf sapi=0 tei=88 nr=0 Aug 11
22:36:20.887: ISDN BR0/2/0 Q921: User RX <- RRf sapi=0 tei=88 nr=1
Cork_CCME(config-if)# Aug 11 22:36:21.507: ISDN BR0/2/0 Q921: User RX
<- INFO sapi=0 tei=87, ns=0 nr=1 Aug 11 22:36:21.507: ISDN BR0/2/0
Q931: RELEASE pd = 8  callref = 0x69
        Cause i = 0x819F - Normal, unspecified Aug 11 22:36:21.515:
ISDN BR0/2/0 Q921: User RX <- INFO sapi=0 tei=86, ns=0 nr=1 Aug 11
22:36:21.515: ISDN BR0/2/0 Q931: RELEASE pd = 8  callref = 0x69
        Cause i = 0x819F - Normal, unspecified Aug 11 22:36:21.543:
ISDN BR0/2/0 Q921: User RX <- RR sapi=0 tei=87 nr=2 Aug 11
22:36:21.555: ISDN BR0/2/0 Q921: User RX <- RR sapi=0 tei=86 nr=2
Cork_CCME(config-if)# Aug 11 22:36:25.803: ISDN BR0/2/0 Q921: User RX
<- DISCp sapi=0 tei=88 Aug 11 22:36:25: %ISDN-6-LAYER2DOWN: Layer 2
for Interface BR0/2/0, TEI 88 changed to down