[cisco-voip] PRI failover

Paul asobihoudai at yahoo.com
Fri Aug 21 16:57:51 EDT 2009


You can only put PRIs in an outbound trunk group. Telco has to configure their side for inbound.

If I remember correctly you put the trunk group on the PRI port setting...where you'd specify the switch type.




----- Original Message ----
From: "Carter, Bill" <bcarter at sentinel.com>
To: Dennis Heim <Dennis.Heim at cdw.com>; cisco-voip at puck.nether.net
Sent: Friday, August 21, 2009 11:14:03 AM
Subject: Re: [cisco-voip] PRI failover

How do you put PRIs in a Hunt Group? I have been trying to figure this out for awhile.

-----Original Message-----
From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Dennis Heim
Sent: Sunday, August 16, 2009 5:01 PM
To: Dennis Heim; Syed Khalid Ali; pocketapl at nm.ru; cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] PRI failover

I mean trunk group.

Dennis Heim
Network Voice Engineer
CDW  Advanced Technology Services
11711 N. Meridian Street, Suite 225
Carmel, IN  46032

317.569.4255 Office
317.569.4201 Fax
317.694.6070 Cell
dennis.heim at cdw.com
www.berbee.com


-----Original Message-----
From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Dennis Heim
Sent: Sunday, August 16, 2009 3:30 PM
To: Syed Khalid Ali; pocketapl at nm.ru; cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] PRI failover

Did you try putting the PRI's in a hunt group?

Dennis Heim
Network Voice Engineer
CDW  Advanced Technology Services
11711 N. Meridian Street, Suite 225
Carmel, IN  46032

317.569.4255 Office
317.569.4201 Fax
317.694.6070 Cell
dennis.heim at cdw.com
www.berbee.com

-----Original Message-----
From: Syed Khalid Ali [mailto:syed.khalid.khursheed at gmail.com] 
Sent: Sunday, August 16, 2009 1:48 PM
To: Dennis Heim; pocketapl at nm.ru; cisco-voip at puck.nether.net
Subject: Re: [cisco-voip] PRI failover

Using H.323 gateway and CCM 4.2

I did configure a secondary dial-peer for larger preference with it is
not working.


On Sun, Aug 16, 2009 at 12:52 AM, Dennis Heim<Dennis.Heim at cdw.com> wrote:
> DO you have any details on your setup?
>
> MGCP/H.323... etc?
>
> Dennis Heim
> Network Voice Engineer
> CDW  Advanced Technology Services
> 11711 N. Meridian Street, Suite 225
> Carmel, IN  46032
>
> 317.569.4255 Office
> 317.569.4201 Fax
> 317.694.6070 Cell
> dennis.heim at cdw.com
> www.berbee.com
>
> -----Original Message-----
> From: cisco-voip-bounces at puck.nether.net [mailto:cisco-voip-bounces at puck.nether.net] On Behalf Of Syed Khalid Ali
> Sent: Saturday, August 15, 2009 9:58 AM
> To: cisco-voip at puck.nether.net
> Subject: [cisco-voip] PRI failover
>
> dear all,
>
> How to failover to secondary pri line.
> I tried the trunk group command but it is not supported on this setup.
>
> --
> Thanks,
> Syed Khalid Ali
> _______________________________________________
> cisco-voip mailing list
> cisco-voip at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>



-- 
Thanks,
Syed Khalid Ali
_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
_______________________________________________
cisco-voip mailing list
cisco-voip at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip



      


More information about the cisco-voip mailing list