That is probably what happened. LEC's like to turn circuits down after 20 or
so minutes of failure.
Do a debug isdn q.921, that will give you the appropriate D channel debug
information, and more then likely help you out with determing the root-cause
of the problem.
-Scott
> -----Original Message-----
> From: George Robbins [mailto:grr@shandakor.tharsis.com]
> Sent: Thursday, May 24, 2001 2:40 PM
> To: cisco-nsp@puck.nether.net; dave@hawk-systems.com
> Subject: Re: serial channels not available = busy signal
> after cold boot
>
>
> Check with the telco to make sure that they didn't turn down the
> ISDN BRI interface when there was an apparent circuit problem.
>
> Check that your t1 controlllers show up and not looped.
>
> George
>
> > From cisco-nsp-request@puck.nether.net Thu May 24 14:25:16 2001
> > Date: Thu, 24 May 2001 14:20:09 -0400
> > X-From_: dave@hawk-systems.com Thu May 24 14:20:08 2001
> > Received-Date: Thu, 24 May 2001 14:20:08 -0400
> > From: "Dave VanAuken" <dave@hawk-systems.com>
> > To: <cisco-nsp@puck.nether.net>
> > Subject: serial channels not available = busy signal after cold boot
> > Old-Date: Thu, 24 May 2001 14:22:07 -0400
> > In-Reply-To:
> <748E5587967C034CAD903153722CF853301B1F@atlmsx.corp.interland.net>
> > Old-X-Envelope-To: cisco-nsp
> > Resent-From: jared@puck.nether.net
> > Resent-Date: Thu, 24 May 2001 14:23:04 -0400
> > Resent-To: cisco-nsp@puck.nether.net
> > X-Mailing-List: <cisco-nsp@puck.nether.net> archive/latest/6438
> > X-Loop: cisco-nsp@puck.nether.net
> > Precedence: list
> > Resent-Sender: cisco-nsp-request@puck.nether.net
> >
> > have an as5300, IOS 12.1 that was turned off and then back on by a
> > company executive (for some unknown reason)... on reboot
> and reload of
> > the config files, everything appears to be in order, but
> dialin is no
> > longer functional. The NAS reports...
> >
> > May 24 12:13:26.071: %ISDN-6-CHAN_UNAVAILABLE: Interface Se0:23
> > Requested Channel 9 is not available
> >
> > this repeats (obviously on different channels for subsequent calls)
> > and the user is told a busy signal has been received.
> >
> > Configuration is included below (was same configuration that was in
> > use prior to the hard boot, and the same configuration to
> my knowledge
> > that was reloaded and rebooted before). Am thinking I am not seeing
> > the forest for the trees here... a look over and comments or
> > suggestions would be appreciated.
> >
> > Thanks
> >
> > Dave
> >
> > Current configuration : 3565 bytes
> > !
> > ! No configuration change since last restart
> > !
> > version 12.1
> > no service single-slot-reload-enable
> > service timestamps debug datetime msec
> > service timestamps log datetime msec
> > service password-encryption
> > !
> > hostname as0
> > !
> > logging rate-limit console 10 except errors
> > aaa new-model
> > aaa authentication login default group radius local
> > aaa authentication login consoleport local
> > aaa authentication ppp default group radius local
> > aaa authorization network default group radius
> > aaa accounting network default wait-start group radius
> > enable secret 5 $1$jqRa$BjijeMpVHfY9U4HdC8Fic/
> > !
> > username admin password 7 063E5F765C4F00
> > spe 1/0 1/3
> > firmware location system:/ucode/mica_port_firmware
> > !
> > !
> > resource-pool disable
> > !
> > clock timezone EST -5
> > clock summer-time EDT recurring
> > clock calendar-valid
> > ip subnet-zero
> > no ip source-route
> > no ip finger
> > ip domain-name nexusinternetsolutions.net
> > ip host dns1 192.50.168.6
> > ip host dns2 192.50.168.7
> > ip name-server 192.50.168.6
> > ip name-server 192.50.168.7
> > !
> > virtual-profile virtual-template 1
> > multilink virtual-template 1
> > isdn switch-type primary-dms100
> > partition flash 2 8 8
> > !
> > !
> > !
> > controller T1 0
> > framing esf
> > clock source line primary
> > linecode b8zs
> > pri-group timeslots 1-24
> > description Bell T1 555-555-3389 > 23B:1D
> > !
> > controller T1 1
> > shutdown
> > clock source line secondary 1
> > !
> > controller T1 2
> > shutdown
> > clock source line secondary 2
> > !
> > controller T1 3
> > shutdown
> > clock source line secondary 3
> > !
> > controller T1 4
> > shutdown
> > clock source line secondary 4
> > !
> > controller T1 5
> > shutdown
> > clock source line secondary 5
> > !
> > controller T1 6
> > shutdown
> > clock source line secondary 6
> > !
> > controller T1 7
> > shutdown
> > clock source line secondary 7
> > !
> > !
> > interface Ethernet0
> > no ip address
> > shutdown
> > !
> > interface Virtual-Template1
> > ip unnumbered FastEthernet0
> > ip tcp header-compression passive
> > no keepalive
> > peer default ip address pool default
> > ppp authentication chap pap
> > ppp multilink
> > multilink max-links 2
> > !
> > interface Serial0
> > no ip address
> > shutdown
> > no fair-queue
> > clockrate 2015232
> > !
> > interface Serial1
> > no ip address
> > shutdown
> > no fair-queue
> > clockrate 2015232
> > !
> > interface Serial2
> > no ip address
> > shutdown
> > no fair-queue
> > clockrate 2015232
> > !
> > interface Serial3
> > no ip address
> > shutdown
> > no fair-queue
> > clockrate 2015232
> > !
> > interface Serial0:23
> > ip unnumbered FastEthernet0
> > encapsulation ppp
> > ip mroute-cache
> > no keepalive
> > dialer-group 1
> > isdn switch-type primary-dms100
> > isdn incoming-voice modem
> > no peer default ip address
> > no fair-queue
> > ppp max-bad-auth 3
> > ppp authentication chap pap
> > ppp multilink
> > !
> > interface FastEthernet0
> > ip address 192.50.168.4 255.255.255.192
> > no ip mroute-cache
> > duplex auto
> > speed auto
> > !
> > interface Group-Async0
> > ip unnumbered FastEthernet0
> > encapsulation ppp
> > async mode interactive
> > peer default ip address pool default
> > no fair-queue
> > ppp max-bad-auth 3
> > ppp authentication chap pap
> > ppp multilink
> > group-range 1 48
> > !
> > ip local pool default 192.50.168.40 192.50.168.62
> > ip default-gateway 192.50.168.1
> > ip classless
> > ip route 0.0.0.0 0.0.0.0 192.50.168.1
> > ip http server
> > !
> > access-list 101 permit ip 192.50.168.0 0.0.0.63 any
> > dialer-list 1 protocol ip permit
> > radius-server host 192.50.168.10 auth-port 1645 acct-port 1646
> > radius-server retransmit 3
> > radius-server key 7 030B5E13051C71
> > banner login ^C
> >
> > This is a secured device.
> > Unauthorized use is prohibited by law.
> >
> > ^C
> > !
> > line con 0
> > login authentication consoleport
> > transport input none
> > line 1 48
> > autoselect during-login
> > autoselect ppp
> > modem Dialin
> > line aux 0
> > line vty 0 4
> > !
> > end
> >
> > as0#
> >
> >
>
This archive was generated by hypermail 2b29 : Sun Aug 04 2002 - 04:12:38 EDT