Chris,
If the GSR is not running full bandwidth, then you'll get similar messages
like "low bandwidth" when you insert a LC that requires OC48 bandwidth.
Micky does not indicate this in his original e-mail so the problem is not
related to the GSR bandwidth.
Alex Yeung
> -----Original Message-----
> From: Piastri, Chris [mailto:cpiastri@cisco.com]
> Sent: Monday, October 29, 2001 12:09 AM
> To: 'micky'; Yeung, Alex
> Cc: cisco-nsp@puck.nether.net; boris@apol.com.tw; Desmarais, Jonathan
> Subject: RE: [nsp] Cisco GSR12012 support 3port GE line card ?
>
>
> You need to make sure that your 12012 is running in full bandwidth mode
> (which is, one clock scheduler card and three switch fabric cards).
>
> If your 12012 was ordered a long time ago then it may have been ordered
> in 1/4 bandwidth config (ie. OC12 per slot with 1x CSC card) - Note this
> is not orderable now. Only E0 cards can be used in this config and E2
> cards (which the 3pt GigE is one) cannot be used in 1/4 bandwidth mode.
>
> If this is the case you'll need to get the extra SFM's and CSC to take
> the 12012 up to full bandwidth (OC48) per slot.
>
> Chris...
>
> > -----Original Message-----
> > From: micky [mailto:micky@apol.com.tw]
> > Sent: Monday, 29 October 2001 12:13 PM
> > To: Yeung, Alex
> > Cc: cisco-nsp@puck.nether.net; boris@apol.com.tw; Desmarais, Jonathan
> > Subject: Re: [nsp] Cisco GSR12012 support 3port GE line card ?
> >
> >
> > Hi Alex Yeung
> >
> > I have tried different slot on GSR 12012,but still didn't work
> > But I inserted into GSR model 12016 and it
> > worked,that's very tricky
> > and ridiculous
> > The two GSRs(12012 and 12016) are running the same IOS version
> > Could you give me more tips or clues ?
> >
> > Special thanks
> > Micky
> > ----- Original Message -----
> > From: "Alex Yeung" <alyeung@cisco.com>
> > To: "micky" <micky@apol.com.tw>; "Desmarais, Jonathan"
> > <JDesmarais@colt-telecom.com>
> > Cc: <cisco-nsp@puck.nether.net>; <boris@apol.com.tw>
> > Sent: Monday, October 29, 2001 8:23 AM
> > Subject: RE: [nsp] Cisco GSR12012 support 3port GE line card ?
> >
> >
> > > >
> > > > Hi Jon
> > > >
> > > > It's strange
> > > > I have used the version on GSR 12016 for a long time,that's
> > fine,no
> > > > any problem
> > > > What's difference between 12012 and 12016 ?
> > >
> > > 12012 is a 12-slot GSR, 12016 is a 16-slot GSR.
> > >
> > > >
> > > >
> > > >
> > > > > You need 12.015S2 at least.
> > >
> > > 3xport GE is supported from 12.0(11)S3.
> > >
> > > > >
> > > > > I have the same issue, try using 12.016S(thelatest) it
> > works well.
> > > > >
> > >
> > > The latest is 12.0(19)S for the GSR.
> > >
> > > Alex Yeung
> > >
> > >
> > > > > Cheers
> > > > > Jon
> > > > >
> > > > > -----Original Message-----
> > > > > From: micky [mailto:micky@apol.com.tw]
> > > > > Sent: 26 October 2001 11:24
> > > > > To: cisco-nsp@puck.nether.net
> > > > > Subject: [nsp] Cisco GSR12012 support 3port GE line card ?
> > > > >
> > > > >
> > > > > Hi Mr.nsp
> > > > >
> > > > > My GSR12012 is running IOS ver 12.0.15s1
> > > > > When I finished inserting the line card,I found card
> > was detected
> > by
> > > > IOS
> > > > > But the front panel led showed "up" ,not "run"
> > > > > It's very strange,this caused GE port to be down
> > > > >
> > > > > Anyone about this condition ?
> > > > >
> > > > > Thanks
> > > > > Have a nice weekend
> > > > > Micky
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > **********************************************************************
> > > > > COLT Telecommunications
> > > > > Registered in England No. 2452736
> > > > > Registered Office: Bishopsgate Court, 4 Norton Folgate,
> > London E1 6DQ
> > > > > Tel. 020 7390 3900
> > > > >
> > > > > This message is subject to and does not create or vary
> > any contractual
> > > > > relationship between COLT Telecommunications, its
> > subsidiaries or
> > > > > affiliates ("COLT") and you. Internet communications
> > are not secure
> > > > > and therefore COLT does not accept legal responsibility for the
> > > > > contents of this message. Any view or opinions
> > expressed are those of
> > > > > the author. The message is intended for the addressee
> > only and its
> > > > > contents and any attached files are strictly
> > confidential. If you have
> > > > > received it in error, please telephone the number
> > above. Thank you.
> > > > >
> > > > >
> > > > >
> > **********************************************************************
> > > >
> > > >
> >
>
This archive was generated by hypermail 2b29 : Sun Aug 04 2002 - 04:13:21 EDT