[cisco-bba] 7204VXR(NPE-G1) running c7200-jk9s-mz.123-14.T3.bin

[Mark Tohill]

Hi Oliver,

TAC Case No. is 604178461 - Tracebacks etc on 7204-NPEG1s x 2 running
c7200-jk9s-mz.123-14.T3.bin.

Oliver, regarding the 'trigger', I was trying to figure this out myself.
These boxes were behaving perfectly for six or seven months and then
this, all of a sudden.

There have been no configuration changes, of note, since then. The only
thing I can think of is I am now logging a suspected spammer on an
extended inbound ACL on our internet-facing interface.

I get entries in logging buffer for this user. Possibly connected to
this is the mention of 'Virtual Exec' messages we got along with the
tracebacks. It's maybe nothing.

Thanks again,
Mark


-----Original Message-----
From: Oliver Boehmer (oboehmer) [mailto:oboehmer at cisco.com] 
Sent: 01 September 2006 09:40
To: Mark Tohill; cisco-bba at puck.nether.net; cisco-nsp at puck.nether.net
Subject: RE: [cisco-bba] 7204VXR(NPE-G1) running
c7200-jk9s-mz.123-14.T3.bin

Mark,

to me, this looks like side-effects of the memory leak, i.e. you're
running out of memory causing all kinds of things. Do you get malloc
failures in the logs? What is the TAC case# so I can take a look?

I do wonder about the PARSER-4-BADCFG message. What is the trigger for
them? Do you do some config via tftp or similar (copy tftp
running-config)?

	oli

Mark Tohill <> wrote on Friday, September 01, 2006 10:15 AM:

> Hello,
> 
> We have 7204-NPEG1s x 2 running c7200-jk9s-mz.123-14.T3.bin. These
> boxes are running BGP(default only), and terminating DSL L2TP VPDN's. 
> 
> We're having a few issues with that image, one involving 'VTemplate
> Manager' tracebacks. According to TAC, this is bugid: 
> 
> CSCeh90534
> Externally found severe defect: Duplicate (D)
> memory leak with micro_block_alloc calling VTEMPLATE Backgr
> 
> Duplicate of :  CSCeg81196, fixed in 12.3(14)T4 and later
> 
> On same boxes, we get the following:
> 
> Aug 31 13:38:15.293: %PARSER-4-BADCFG: Unexpected end of
> configuration file. 
> Aug 31 13:38:15.297: %PARSER-4-BADCFG: Unexpected end of
> configuration file. 
> 
> This is having the interesting side effect of not 'saving' a Loopback
> and GRE Tunnel interface to the running config file. When we show
> specific interface configurations, it's fine. See below:  
> 
> #sh run int tunnel 0
> Building configuration...
> Current configuration : 136 bytes
> !
> interface Tunnel0
>  ip address 192.168.200.2 255.255.255.252
>  tunnel source GigabitEthernet0/2.200
>  tunnel destination a.b.c.d
> end
> 
> #sh run int loopback 0
> Building configuration...
> Current configuration : 111 bytes
> !
> interface Loopback0
>  description VPDN Tunnel Endpoint
>  ip address a.b.c.d 255.255.255.255
> end
> 
> So we know the interfaces are there, being routed over, but we you do
> an ordinary 'show run', they're configs are not complete..IP
> addressing gone.  
> 
> #sh running-config | begin Tunnel0
> interface Tunnel0
>  !
>  interface Loopback0
>  description VPDN Tunnel Endpoint
> !
> 
> Therefore we can't make any changes to the config, we'll loose them
> when we save to startup!! The loopback is fairly critical, it
> terminates the L2TP tunnel, an on reboot, the VPDN sessions will not
> come up since there are no tunnels to carry them.   
> 
> Has anyone encounterd this problem? We have been advised by TAC to
> upgrade to 12.4 mainline, which is fine, but I cannot get info
> regarding the config file corruption.  
> 
> Any experiences/ideas appreciated.
> 
> Mark