[cisco-bba] [Fwd: PPPoVPDN and VA bandwidth]
Oliver Boehmer (oboehmer)
oboehmer at cisco.com
Sat Jan 13 03:56:00 EST 2007
I agree, looks like client-initiated L2TP doesn't pass any meaningful
connect-speed to the LNS. Could be an interesting discussion which speed
to pass (as there are potentially multiple ingress interfaces using this
tunnel, so not as easy as on a traditional L2TP LAC), but you can
configure a bandwidth on the vtemplate on the LNS to workaround this,
and this will be used (you could even apply this on a per-user bases
using lcp:interface-config="bandwidth ...").
default config shows 100Mbit:
MHOP-LNS#sh int vi2.1
Virtual-Access2.1 is up, line protocol is up
Hardware is Virtual Access interface
Interface is unnumbered. Using address of Loopback0 (10.0.0.3)
MTU 1500 bytes, BW 100000 Kbit, DLY 100000 usec,
MHOP-LNS#conf t
Enter configuration commands, one per line. End with CNTL/Z.
MHOP-LNS(config)#int virtual-te 1
MHOP-LNS(config-if)#band
MHOP-LNS(config-if)#bandwidth 2000
MHOP-LNS(config-if)#^Z
MHOP-LNS#
MHOP-LNS#clear vpdn tunnel l2tp all
Clear all L2TP tunnels? [confirm]yStarting to clear the tunnel
MHOP-LNS#
after reestablishing the session we see this reflected on the VAI:
MHOP-LNS#sh int vi2.1
Virtual-Access2.1 is up, line protocol is up
Hardware is Virtual Access interface
Interface is unnumbered. Using address of Loopback0 (10.0.0.3)
MTU 1500 bytes, BW 2000 Kbit, DLY 100000 usec,
oli
cisco-bba-bounces at puck.nether.net <> wrote on :
> Anybody? I am coming to a conclusion that this is a
> limitation currently.
>
> -------- Original Message --------
> Subject: [cisco-bba] PPPoVPDN and VA bandwidth
> Date: Tue, 09 Jan 2007 23:57:51 +0100
> From: Gaurav Sabharwal <gaurav at inwire.net>
> To: cisco-bba at puck.nether.net
>
> RFC 2661 mentions Rx and Tx Connect Speed AVP that should be
> part of the
> ICCN. However, while implementing client initiated L2TP and doing a
> debug vpdn l2x-packets, I notice that the Connect Speed shown
> on the CPE
> (Cisco 876) and the LNS (Cisco 7206VXR) is set to 0. This sets the
> virtual-access and the virtual-ppp speeds to 100 Mbps.
>
> *Jan 2 09:27:40.067: uid:48 Tnl/Sn 40583/143 L2TP: Parse
> AVP 0, len 8,
> flag 0x8000 (M)
> *Jan 2 09:27:40.067: uid:48 Tnl/Sn 40583/143 L2TP: Parse ICCN
> *Jan 2 09:27:40.067: uid:48 Tnl/Sn 40583/143 L2TP: Parse AVP 24,
> len 10, flag 0x8000 (M)
> *Jan 2 09:27:40.067: uid:48 Tnl/Sn 40583/143 L2TP: Connect Speed 0
> *Jan 2 09:27:40.071: uid:48 Tnl/Sn 40583/143 L2TP: Parse AVP 19,
> len 10, flag 0x8000 (M)
> *Jan 2 09:27:40.071: uid:48 Tnl/Sn 40583/143 L2TP: Framing Type 1
>
> I assume that setting incorrect bandwidth on the interface would cause
> problems if we were to implement QoS?
>
> Is there a way to resolve the issue and make sure that the Tx
> speed sent
> by the CPE are correct?
>
> Thanks,
> - Gaurav
> _______________________________________________
> cisco-bba mailing list
> cisco-bba at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-bba
>
> _______________________________________________
> cisco-bba mailing list
> cisco-bba at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-bba
More information about the cisco-bba
mailing list