[cisco-bba] gigabit ethernet help

[Sunet Sysadmin]

Hi All,
thanks guys for your help. as james and stavros where mentioning telstra 
usually after the demarcation point it is on MMOF. but the site survey 
officer came in and suggested single mode after demarcation point( which 
as far as i know and understand is not really required as the distance 
between demarcation to our rack is 500 mt) so ordered single mode from 
the data centre to run from demarcation to our gateway. Launched an 
complaint with telstra and found out that telstra placed an OMC in their 
rack which is taking single mode in and MM out. so it is a bit of mess 
which is getting cleared know. so hope fully in the next couple of weeks 
will get the link up.

thanks for you suggestions.

cheers
phani.


Systems Administrator
+61 03 5227 6888

With over 20,000 products
online, ordering on line is easy at bcc
visit www.bcccomputers.com.au





Erich Hohermuth wrote:

>Hi Phani,
>
>SX Modules are for MultiMode fibre connections. If you have SingleMode
>fibres you need either a LX (1310nm) ~10km or a ZX (1550nm) ~ 40 km
>module. Please ask the Telco (Telstra) what they required. 
>
>Regards
>	Erich
>
>
>  
>
>>Telstra IGR(telco australia)-----------single mode 
>>fibre-------------demarcation point data centre ----------------single 
>>mode  fibre flat SC connector --------------- 7200 series router 
>>1000Base SX module
>>
>>The problem is i can't get the interface up and even if i plug/unplug 
>>the single fibre optic the router dowsn't seems be reacting by showing 
>>link up or down.
>>
>>The lights on the Gigabit interface keep flashing  Tx,Rx,link in 
>>1,2,3,1,2,3 ---- pattern.
>>
>>any suggestions or any help is very much appreciated.
>>
>>hadar#show diag
>>Slot 0:
>>      I/O Controller Port adapter
>>      Port adapter is analyzed
>>      Port adapter insertion time 1d00h ago
>>      EEPROM contents at hardware discovery:
>>      Hardware revision 2.1           Board revision B0
>>      Serial number     21855274      Part number    73-4093-03
>>      FRU Part Number:  C7200-I/O=
>>
>>      Test history      0x0           RMA number     00-00-00
>>      EEPROM format version 1
>>      EEPROM contents (hex):
>>        0x20: 01 36 02 01 01 4D 7C 2A 49 0F FD 03 00 00 00 00
>>        0x30: 58 08 4A 00 00 10 08 00 00 00 FF FF FF FF FF FF
>>
>>Slot 1:
>>      Gigabit Ethernet Port adapter, 1 port
>>      Port adapter is analyzed
>>      Port adapter insertion time 1d00h ago
>>      EEPROM contents at hardware discovery:
>>      Hardware revision 1.0           Board revision A1
>>      Serial number     22579772      Part number    73-3144-03
>>      FRU Part Number:  PA-1GE=
>>
>>      Test history      0x0           RMA number     00-00-00
>>      EEPROM format version 1
>>      EEPROM contents (hex):
>>        0x20: 01 98 01 00 01 58 8A 3C 49 0C 48 03 00 00 00 00
>>        0x30: 51 02 73 00 00 00 00 00 00 01 FF FF FF FF FF FF
>>
>>Slot 2:
>>      Fastethernet (TX-ISL) Port adapter, 2 ports
>>      Port adapter is analyzed
>>      Port adapter insertion time 1d00h ago
>>      EEPROM contents at hardware discovery:
>>      Hardware revision 2.0           Board revision B0
>>      Serial number     16412105      Part number    73-2618-03
>>      FRU Part Number:  PA-2FE-TX=, PA-2FEISL-TX=
>>
>>      Test history      0x0           RMA number     00-00-00
>>      EEPROM format version 1
>>      EEPROM contents (hex):
>>        0x20: 01 6C 02 00 00 FA 6D C9 49 0A 3A 03 00 00 00 00
>>        0x30: 58 00 00 00 99 12 29 00 00 00 FF FF FF FF FF 00
>>
>>hadar#show ver
>>Cisco Internetwork Operating System Software
>>IOS (tm) 7200 Software (C7200-IK9S-M), Version 12.2(8)T5,  RELEASE 
>>SOFTWARE (fc1)
>>TAC Support: http://www.cisco.com/tac
>>Copyright (c) 1986-2002 by cisco Systems, Inc.
>>Compiled Sat 22-Jun-02 16:20 by ccai
>>Image text-base: 0x60008940, data-base: 0x6173A000
>>
>>ROM: System Bootstrap, Version 12.1(20000824:081033) 
>>[dbeazley-cosmos_e_LATEST 101], DEVELOPMENT SOFTWARE
>>BOOTLDR: 7200 Software (C7200-BOOT-M), Version 12.0(15)S1, EARLY 
>>DEPLOYMENT RELEASE SOFTWARE (fc1)
>>
>>hadar uptime is 1 day, 25 minutes
>>System returned to ROM by power-on
>>System image file is "sup-slot0:/c7200-ik9s-mz.122-8.T5.bin"
>>
>>cisco 7204VXR (NPE300) processor (revision D) with 122880K/40960K
>>
>>
>>
>>cheers
>>phani.
>>
>>_______________________________________________
>>cisco-bba mailing list
>>cisco-bba at puck.nether.net
>>https://puck.nether.net/mailman/listinfo/cisco-bba
>>    
>>