[cisco-nas] AS5350 Internal clocking.

[Richard Greasley]

Ok thanks, I shall try later and get back to you.

Best regards,
Richardg;

----- Original Message ----- 
From: "Aaron Leonard" <Aaron at cisco.com>
To: "Aaron Leonard" <Aaron at cisco.com>
Cc: "Richard Greasley" <rjcg at caribsurf.com>; "Aaron Leonard"
<Aaron at cisco.com>; <cisco-nas at puck.nether.net>
Sent: Monday, September 22, 2003 4:58 PM
Subject: Re: [cisco-nas] AS5350 Internal clocking.


> Turns out that I already filed that DDTS back in '01
> and it was fixed in 12.2(7.1)T / 12.2(7.4):
>
> CSCdv83199
> Externally found minor defect: Resolved (R)
> unhide and document dial-tdm-clock freerun option
>
> In the MEANTIME, "dial-tdm-clock" has been hidden as it
> has been deprecated in favor of the better designed
> "tdm clock" command:
>
> 5400HPX-3(config)#tdm clock priority 1 ?
>   <1-7>     Slot/Port number (e.g. 1/1)
>   external  Select external reference(Bits) clock
>   freerun   Select local oscillator clock
>
> Evidently "tdm clock" was introduced on the AS5000s in
> 12.2(11)T ... unfortunately, our documentation hasn't caught
> up with things yet ...
>
> Aaron
>
> ---
>
> > It looks like "freerun" is hidden ... so just enter it:
>
> > dial-tdm-clock priority 1 freerun
>
> > In 12.2(11)T, the whole "dial-tdm-clock" command is hidden :-(.
> > I'm going to check with current IOS, then if it's still hidden,
> > I'll file a DDTS to unhide it.
>
> > Aaron
>
> > ---
>
> > > Thanks,
> > > However I'm still not getting that option...
> > > as5350-1(config)#dial-tdm-clock priority 1 ?
> > >   <1-3>     Slot number
> > >   external  Select external reference(Bits) clock
>
> > > I've included a copy of "show version"
>
> > > Cisco Internetwork Operating System Software
> > > IOS (tm) 5350 Software (C5350-IS-M), Version 12.2(2)XB6, EARLY
DEPLOYMENT
> > > RELEASE SOFTWARE (fc1)
> > > TAC Support: http://www.cisco.com/tac/
> > > Copyright (c) 1986-2002 by cisco Systems, Inc.
> > > Compiled Mon 17-Jun-02 16:53 by hwcheng
> > > Image text-base: 0x600089C8, data-base: 0x61200000
>
> > > ROM: System Bootstrap, Version 12.2(1r)1, RELEASE SOFTWARE (fc1)
> > > BOOTLDR: 5350 Software (C5350-BOOT-M), Experimental Version
> > > 12.1(20000922:142008) [nag-flo_t_0110 101]
>
> > > as5350-1 uptime is 47 minutes
> > > System returned to ROM by reload at 18:27:22 UTC Mon Sep 22 2003
> > > System restarted at 18:28:50 UTC Mon Sep 22 2003
> > > System image file is "flash:c5350-is-mz.122-2.XB6.bin"
>
> > > cisco AS5350 (R7K) processor (revision T) with 131072K/65536K bytes of
> > > memory.
> > > Processor board ID JAE065000H5
> > > R7000 CPU at 250Mhz, Implementation 39, Rev 1.0, 256KB L2, 2048KB L3
Cache
> > > Last reset from IOS reload
> > > Bridging software.
> > > X.25 software, Version 3.0.0.
> > > SuperLAT software (copyright 1990 by Meridian Technology Corp).
> > > Primary Rate ISDN software, Version 1.1.
> > > Manufacture Cookie Info:
> > >  EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x32,
> > >  Board Hardware Version 3.33, Item Number 800-5171-02,
> > >  Board Revision B0, Serial Number JAE065000H5,
> > >  PLD/ISP Version 2.2,  Manufacture Date 17-Dec-2002.
> > > Processor 0x14, MAC Address 0x0B46825D40
> > > Backplane HW Revision 1.0, Flash Type 5V
> > > 2 FastEthernet/IEEE 802.3 interface(s)
> > > 194 Serial network interface(s)
> > > 216 terminal line(s)
> > > 8 Channelized T1/PRI port(s)
> > > 512K bytes of non-volatile configuration memory.
> > > 32768K bytes of processor board System flash (Read/Write)
> > > 8192K bytes of processor board Boot flash (Read/Write)
>
> > > Configuration register is 0x2102
>
> > > regards,
> > > Richardg;
>
> > > ----- Original Message -----
> > > From: "Aaron Leonard" <Aaron at cisco.com>
> > > To: "Richard Greasley" <rjcg at caribsurf.com>
> > > Cc: <cisco-nas at puck.nether.net>
> > > Sent: Monday, September 22, 2003 1:51 PM
> > > Subject: Re: [cisco-nas] AS5350 Internal clocking.
>
>
> > > > > Hello, I know on an AS5300 when configuring the T1 controller
while in
> > > > > "controller-config" mode you  enter
"AS5300(config-controller)#clock
> > > source
> > > > > internal" in order to get internal clocking done on the T1s.
> > > > > I have now, an AS5350 and I can't find the command option, is
there a
> > > way to
> > > > > do internal clocking on an AS5350?
> > > >
> > > > > Thanks and regards,
> > > > > Richardg;
> > > >
> > > > On the newer platforms (AS5350/5400/5850), we use the
> > > > dial-tdm-clock command for this.  Specificially, if you
> > > > want the platform's TDM clock to freerun, use:
> > > >
> > > > dial-tdm-clock priority <n> freerun
> > > >
> > > > where <n> is a higher priority than any other dial-tdm-clock
> > > > source.  (1 being the highest.)
> > > >
> > > >
> > >
http://www.cisco.com/en/US/products/sw/iosswrel/ps5187/products_command_reference_chapter09186a008017d9d0.html#1062252
> > > >
> > > > Aaron
> > > > _______________________________________________
> > > > cisco-nas mailing list
> > > > cisco-nas at puck.nether.net
> > > > https://puck.nether.net/mailman/listinfo/cisco-nas
> > > >
>