[cisco-nas] Cisco 3640 does not collect Calling ID and Called ID

[Souphonh]

Dear Aaron,

Thanks for your reply. With our digital modem NAS (AS5300) that uses R2 connected to PSTN also cannot collect the Calling ID, we can collect only the Called ID. Could you please suggest the configuration to collect both Calling and Called ID. The following is the log of my digital modem csm:

  ras2#sh modem cs
  ras2#sh modem csm 1/9
  MODEM_INFO: slot 1, port 9, unit 0, tone r2-compelled, modem_mask=0x0000, modem_port_offset=0
  tty_hwidb=0x620749E0, modem_tty=0x61A48C84, oobp_info=0x00000000, modem_pool=0x6180204C
  tty statbits=0x20090440, statbits2=0x00000001
  tty capabilities=0x00018C01, capabilities2=0x00008000
  modem_status(0x2802): VDEV_STATUS_ACTIVE_CALL.VDEV_STATUS_ALLOCATED.VDEV_STATUS_NEGOTIATED.
  device capabilities=0x0000AFDE
  csm_state(0x0209)=CSM_IC7_CONNECTED, csm_event_proc=0x6017D828, current call thru CAS line
  invalid_event_count=0, wdt_timeout_count=0
  wdt_timestamp_started is not activated
  wait_for_dialing:False, wait_for_bchan:False
  pri_chnl=TDM_PRI_STREAM(s0, u1, c7), modem_chnl=TDM_MODEM_STREAM(s1, c9)
  physical tdm port = 9, Backplane TDM Stream = 1, Channel = 1
  dchan_idb_start_index=0, dchan_idb_index=0, call_id=0x0F86, bchan_num=6
  csm_event=CSM_EVENT_DSX0_CONNECTED, cause=0x000E
  Last 8 CSM states and events:
     Number States                             Events
     [0]    CSM_IC6_WAIT_FOR_CONNECT           CSM_EVENT_DSX0_CONNECTED
     [1]    CSM_IC7_CONNECTED                  CSM_EVENT_DSX0_DISCONNECTED
     [2]    CSM_OC8_DISCONNECTING              CSM_EVENT_NONE
     [3]    CSM_IC3_WAIT_FOR_RES_RESP          CSM_EVENT_RESOURCE_OK
     [4]    CSM_IC6_WAIT_FOR_CONNECT           CSM_EVENT_DSX0_CONNECTED
     [5]    CSM_OC6_CONNECTED                  CSM_EVENT_NONE
     [6]    CSM_IC3_WAIT_FOR_RES_RESP          CSM_EVENT_RESOURCE_OK
     [7]    CSM_IC6_WAIT_FOR_CONNECT           CSM_EVENT_DSX0_CONNECTED
  ring_no_answer=7, ic_failure=12, ic_complete=274
  dial_failure=0, oc_failure=0, oc_complete=0
  oc_busy=0, oc_no_dial_tone=0, oc_dial_timeout=0
  remote_link_disc=65, stat_busyout=0, stat_modem_reset=0
  oobp_failure=0
  call_duration_started=4w0d, call_duration_ended=00:00:00, total_call_duration=3d12h
  The calling party phone number =
  The called party phone number  = 125
  total_free_rbs_timeslot = 36, total_busy_rbs_timeslot = 0, total_dynamic_busy_rbs_timeslot = 0, total_static_busy_rbs_timeslot = 0,
  total_sw56_rbs_timeslot = 0, total_sw56_rbs_static_bo_ts = 0,
  total_free_isdn_channels = 0, total_auto_busy_isdn_channels = 0,
  min_free_modem_threshold = 0

As above log, there is no calling party phone number, but the called party phone number is '125' our access phone number for the NAS. 

 
Regards,
Souphonh


----- Original Message ----- 
From: "Aaron Leonard" <Aaron at cisco.com>
To: "Souphonh" <souphonh at laopdr.com>
Cc: <cisco-nas at puck.nether.net>
Sent: Tuesday, April 06, 2004 11:03 AM
Subject: Re: [cisco-nas] Cisco 3640 does not collect Calling ID and Called ID


> Sorry, there is no way to collect this information from
> the NM-AM (or any other analog modems) in a Cisco router.
> To collect ANI and DNIS (calling / called number), you must
> use a digital modem (for example, in the 3640, you would
> use NM-DM MICA modems) and a signaling method that supports
> both ANI and DNIS (for example, ISDN or R2.)
> 
> Aaron
> 
> ---
> 
> > I am using cisco 3640 and analog module for dial up server. I have problem to get 3640 collecting Calling and Called ID from PSTN. Could you please suggest how can I configure our NAS to collect such information. The following is my modem csm log:
> 
> >   ras3#sh modem csm 1/7
> >   Modem 1/7, line 40 (analog)
> >   CSM status: CALL_ACTIVE
> >   CSM current state(0x00000006): CONNECTED_STATE
> >   CSM last event: MODEM_CONNECTED, cause: 0x0000
> >   current call thru CAS line; call_id 0, bchan_num -1
> >   The calling party phone number:
> >   The called party phone number:
> >   wdt timer is not activated
> >   invalid_events 0, wdt_timeouts 0
> >   ic_failure 43, ic_complete 363, oc_failure 0, oc_complete 0
> >   oc_busy 0, remote_link_disc 0, busyout 0, modem_reset 0
> >   call started 2w3d, call ended 00:00:00, total modem active time 3d03h
> >   tty_hwidb 0x6290B674, modem_tty 0x62909DCC, modem_pool 0x625C1BB0
> >   total pri d-channels 0, last used pri d-channel 0
> >   total_free_rbs_timeslot 0, total_busy_rbs_timeslot 0, min_free_modem_threshold 6
> 
> > As above log, there is no value for called and calling party phone number.
> 
> > Regards,
> > Souphonh
> 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://puck.nether.net/pipermail/cisco-nas/attachments/20040406/8fde0186/attachment.html