[cisco-nas] local user with static ip

[Tassos Chatzithomaoglou]

Does this (dialer pool-member) mean i have to remove "dialer rotary-group 1" from "int 
Serial0:15" ?


Aaron Leonard wrote:

> I'd recommend that you do this with a dialer profile.
> 
> interface dialer 2
>  ip unnumbered loopback 0
>  peer default ip address 10.10.10.10
>  dialer remote-name testuser
>  dialer pool 1
>  ppp authentication pap chap callin
> interface dialer 3
>  ip unnumbered loopback 0
>  peer default ip address 10.10.10.11
>  dialer remote-name DUMMY  dialer pool 1  ppp authentication pap chap 
> callin
> interface serial 0:15
>  dialer pool-member 3
>  ppp authentication pap chap callin RADIUS-AAA
>  ppp authorization RADIUS-AAA
>  ppp accounting RADIUS-AAA
> no virtual-profile if-needed
> 
> So the users that need static addresses can get dialer profiles, while
> the rest of the users will get virtual profiles.
> 
> Why did I configure the dummy dialer profile?  Because, if you have
> exactly one dialer profile, then all calls into the corresponding
> dialer pool-members will bind to that dialer profile, rather than
> to the virtual template.
> 
> Aaron
> 
> ---
> 
>> I'm using the following config (some non-important parts are missing) 
>> for a dialup scenario:
> 
> 
>> 5300 (12.2(15)T9)
>> !--------------------------------------------------------
>> !
>> username testuser password 0 testpass
>> !
>> virtual-profile if-needed
>> virtual-profile virtual-template 1
>> !
>> controller E1 0
>>   clock source line primary
>>   pri-group timeslots 1-31
>> !
>> interface Virtual-Template1
>>   ip unnumbered Loopback0
>>   peer default ip address pool test
>>   ppp authentication pap chap callin RADIUS-AAA
>>   ppp authorization RADIUS-AAA
>>   ppp accounting RADIUS-AAA
>> !
>> interface Serial0:15
>>   ip unnumbered Loopback0
>>   encapsulation ppp
>>   dialer rotary-group 1
>>   dialer-group 1
>>   isdn switch-type primary-net5
>>   isdn incoming-voice modem
>> !
>> interface Group-Async1
>>   ip unnumbered Loopback0
>>   encapsulation ppp
>>   async dynamic routing
>>   async mode interactive
>>   peer default ip address pool test
>>   ppp authentication pap chap callin RADIUS-AAA
>>   ppp authorization RADIUS-AAA
>>   ppp accounting RADIUS-AAA
>>   group-range 1 30
>> !
>> interface Dialer1
>>   ip unnumbered Loopback0
>>   encapsulation ppp
>>   dialer in-band
>>   dialer idle-timeout 1200 either
>>   dialer-group 1
>>   peer default ip address pool test
>>   ppp authentication pap chap callin RADIUS-AAA
>>   ppp authorization RADIUS-AAA
>>   ppp accounting RADIUS-AAA
>> !
>> ip local pool test x.x.x.x y.y.y.y
>> !
>> dialer-list 1 protocol ip list 101
>> access-list 101 permit ip any any
>> !--------------------------------------------------------
> 
> 
>> aaa method "RADIUS-AAA" does local aaa first and then radius aaa.
> 
> 
> 
>> I'm trying to make the local defined user "testuser" to get a static 
>> ip (10.10.10.10)
>> whenever he calls into this router (he gets a dynamic instead). I 
>> suppose this needs a
>> "dialer map" configuration under "dialer 1", but i would like your 
>> help here.
>> Is this possible without affecting all the other (dynamic/static) users?
> 
> 
> 
>> -- 
>> ***************************************
>>        Chatzithomaoglou Anastasios
>> Network Design & Development Department
>>               FORTHnet S.A.
>>           <achatz at forthnet.gr>
>> ***************************************
> 
> 
>> _______________________________________________
>> cisco-nas mailing list
>> cisco-nas at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/cisco-nas
> 
> 

-- 
***************************************
       Chatzithomaoglou Anastasios
Network Design & Development Department
              FORTHnet S.A.
          <achatz at forthnet.gr>
***************************************