[cisco-nas] Cisco AS5350 configuration as a modem pool

Fri Apr 13 12:57:16 EDT 2018

Hi Matthew,

Looks like your AS5350 has voice-only DSPs (PVDM2?), not the modem-capable DSPs
(NextPort.)  So no modem for you.

If you have $399 in your pocket, looks like this ebay guy has what you need:
https://www.ebay.com/itm/Cisco-AS5350-AS535-With-1-8PRI-Card-2-NP108-Cards-FULLY-TESTED/142707587318?hash=item213a08f8f6:g:aJoAAOSwK7pamGjq

Cheers,

Aaron

--------------------------------------------------------------------------------

On 4/12/2018 3:28 PM, matthew at corp.crocker.com (Matthew Crocker) wrote:
>
>  
>
> Hello,
>
>  
>
>   I have a new-to-me Cisco AS5350 that I’m trying to get configured as a modem
> pool.   I can’t get it to accept the commands that worked on my old AS5400
>
>  
>
> My AS5400 died and I’m hoping an AS5350 can take its place.  I believe the
> AS5350XM has Flex DSPs installed,  not sure how to get the list of DSP resources.
>
>  
>
>  
>
> *AS5350#show hardware *
>
> *Cisco IOS Software, 5350 Software (C5350-IS-M), Version 12.4(11)XW3, RELEASE
> SOFTWARE (fc3)*
>
> *Technical Support: http://www.cisco.com/techsupport*
>
> *Copyright (c) 1986-2007 by Cisco Systems, Inc.*
>
> *Compiled Fri 17-Aug-07 03:02 by prod_rel_team*
>
> * *
>
> *ROM: System Bootstrap, Version 12.4(22r)T, RELEASE SOFTWARE (fc1)*
>
> * *
>
> *AS5350 uptime is 3 hours, 26 minutes*
>
> *System returned to ROM by power-on*
>
> *System image file is "flash:c5350xm-is-mz.124-11.XW3.bin"*
>
> * *
>
> *Cisco AS5350XM (BCM) processor (revision 0x22) with 393215K/131072K bytes of
> memory.*
>
> *Processor board ID JAE1245ZRSN*
>
> *SB-1 CPU at 750MHz, Implementation 1025, Rev 0.3, 256KB L2 Cache*
>
> *Last reset from power-on*
>
> *Manufacture Cookie Info:*
>
> *EEPROM Version 0x4, Board ID 0x4C3,*
>
> *Board Hardware Version 2.7, Item Number 800-6571779-03,*
>
> *Board Revision B0, Serial Number JAE1245ZRSN.*
>
> *Processor 0x0, MAC Address 0022.9158.1a10*
>
> *2 Gigabit Ethernet interfaces*
>
> *34 Serial interfaces*
>
> *4 Channelized T1/PRI ports*
>
> *512K bytes of NVRAM.*
>
> *126000K bytes of ATA External CompactFlash (Read/Write)*
>
> * *
>
> *Configuration register is 0x2102*
>
>  
>
> Calls are coming in but it can’t find a DSP resource
>
>  
>
> %CALLTRKR-6-CALL_RECORD: ct_hndl=18, service=None, origin=Answer,
> category=SyncData, DS0 slot/port/ds1/chan=1/0/0/22, called=##########,
> calling=(n/a), resource slot/port=(n/a)/(n/a), userid=(n/a), ip=0.0.0.0,
> account id=243, setup=11/18/2008 04:54:29, conn=0.00, phys=0.00, service=0.00,
> authen=0.00, init-rx/tx b-rate=0/0, rx/tx chars=0/0, charged units=0,
> time=0.01, disc subsys=CSM, disc code=0x1A, disc text=Failed to find DSP
> resource, sig type=Unknwn
>
>  
>
>  
>
>  
>
> It will not accept the group-range command in Interface Async0.  Currently
> calls are coming in on a PRI and I would like all calls to be answered by a
> modem with RADIUS Authentication.
>
> Ultmately I would like to eliminate the PRI and have the calls come in via
> SIP.  Yes, I know PPP over dialup modem over SIP/g711u is dumb but that is the
> world we live in today
>
>  
>
>  
>
> Here is my config:
>
>  
>
> version 12.4
>
> service timestamps debug datetime msec
>
> service timestamps log datetime msec
>
> no service password-encryption
>
> !
>
> hostname AS5350
>
> !
>
> boot-start-marker
>
> no boot startup-test
>
> boot-end-marker
>
> !
>
> enable secret
>
> !
>
> !
>
> !
>
> resource-pool disable
>
> aaa new-model
>
> !
>
> !
>
> aaa authentication ppp default local group radius none
>
> aaa authorization network default group radius none
>
> aaa accounting delay-start
>
> aaa accounting update newinfo
>
> aaa accounting network default start-stop group radius
>
> !
>
> !
>
> aaa session-id common
>
> calltracker enable
>
> calltracker history max-size 30
>
> calltracker call-record verbose
>
> voice-card 1
>
> no local-bypass
>
> !
>
> voice-card 2
>
> no local-bypass
>
> !
>
> voice-card 3
>
> no local-bypass
>
> !
>
> no ip source-route
>
> !
>
> !
>
> ip cef
>
> ip name-server A.B.C.D
>
> ip name-server A.B.C.D
>
> !
>
> !
>
> multilink virtual-template 1
>
> multilink bundle-name authenticated
>
> vpdn enable
>
> !
>
> isdn switch-type primary-ni
>
> !
>
> !
>
> voice service voip
>
>  fax protocol pass-through g711ulaw
>
> !
>
> !
>
> !
>
> !
>
> !
>
> !
>
> !
>
> !
>
> !
>
> !
>
> !
>
> !
>
> !
>
> !
>
> !
>
> username matthew privilege 15
>
> archive
>
> log config
>
>   hidekeys
>
> !
>
> !
>
> controller T1 1/0
>
> framing esf
>
> fdl ansi
>
> linecode b8zs
>
> cablelength short 133
>
> pri-group timeslots 1-24
>
> description " PRI 0"
>
> !
>
> controller T1 1/1
>
> framing sf
>
> linecode ami
>
> !
>
> controller T1 3/0
>
> framing sf
>
> linecode ami
>
> !
>
> controller T1 3/1
>
> framing sf
>
> linecode ami
>
> !
>
> interface Loopback0
>
> ip address A.B.C.D 255.255.255.224
>
> no ip mroute-cache
>
> !
>
> interface GigabitEthernet0/0
>
> ip address A.B.C.D 255.255.255.252
>
> duplex auto
>
> speed auto
>
> negotiation auto
>
> !
>
> interface GigabitEthernet0/1
>
> ip address A.B.C.D 255.255.255.0
>
> duplex auto
>
> speed auto
>
> negotiation auto
>
> !
>
> interface Serial0/0
>
> no ip address
>
> shutdown
>
> clock rate 2000000
>
> !
>
> interface Serial0/1
>
> no ip address
>
> shutdown
>
> clock rate 2000000
>
> !
>
> interface Serial1/0:23
>
> no ip address
>
> encapsulation ppp
>
> dialer rotary-group 1
>
> dialer-group 1
>
> isdn switch-type primary-ni
>
> isdn incoming-voice modem
>
> no fair-queue
>
> no cdp enable
>
> !
>
> interface Virtual-Template1
>
>  ip unnumbered GigabitEthernet0/0
>
> ip tcp header-compression
>
> load-interval 60
>
> peer default ip address pool IP-POOL
>
> ppp authentication pap
>
> ppp multilink
>
> !
>
> interface Dialer1
>
> ip unnumbered Loopback0
>
> encapsulation ppp
>
> no ip mroute-cache
>
> dialer in-band
>
> dialer idle-timeout 300
>
> dialer-group 1
>
> peer default ip address pool IP-POOL
>
> no fair-queue
>
> no cdp enable
>
> ppp authentication chap pap callin
>
> ppp multilink
>
> !
>
> interface Group-Async0
>
> physical-layer async
>
> ip unnumbered Loopback0
>
> encapsulation ppp
>
> no ip mroute-cache
>
> async mode interactive
>
> peer default ip address pool IP-POOL
>
> ppp authentication chap pap callin
>
> !
>
> interface Group-Async1
>
> physical-layer async
>
> ip unnumbered GigabitEthernet0/0
>
> encapsulation ppp
>
> ip tcp header-compression
>
> no ip mroute-cache
>
> dialer in-band
>
> dialer idle-timeout 1800
>
> dialer-group 1
>
> async mode dedicated
>
> peer default ip address pool IP-POOL
>
> no fair-queue
>
> ppp authentication pap
>
> ppp multilink
>
> !
>
> ip local pool IP-POOL A.B.C.D A.B.C.D
>
> ip default-gateway A.B.C.D
>
> !
>
> ip route 0.0.0.0 0.0.0.0 A.B.C.D
>
>  
>
> no ip http server
>
> !
>
> !
>
> !
>
> ip access-list extended Deny_The_Bad_Stuff
>
> ip radius source-interface GigabitEthernet0/0
>
> dialer-list 1 protocol ip permit
>
> !
>
> !
>
> !
>
> radius-server host A.B.C.D auth-port 1812 acct-port 1813
>
> radius-server key 7
>
> radius-server authorization default Framed-Protocol ppp
>
> !
>
> control-plane
>
> !
>
> !        
>
> !
>
> voice-port 1/0:D
>
> !
>
> !
>
> !
>
> !
>
> ss7 mtp2-variant Bellcore 0
>
> ss7 mtp2-variant Bellcore 1
>
> ss7 mtp2-variant Bellcore 2
>
> ss7 mtp2-variant Bellcore 3
>
> !
>
> line con 0
>
> line aux 0
>
> no flush-at-activation
>
> autoselect during-login
>
> autoselect ppp
>
> line vty 0 4
>
> !
>
> scheduler allocate 10000 400
>
> end
>
>  
>
> -Matt
>
>  
>
> -- 
>
> Matthew Crocker
>
> Crocker Communications, Inc.
>
> President
>
>
>
> _______________________________________________
> cisco-nas mailing list
> cisco-nas at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nas

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://puck.nether.net/pipermail/cisco-nas/attachments/20180413/6ee94a4b/attachment-0001.html>