<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META content="text/html; charset=iso-8859-1" http-equiv=Content-Type>
<META name=GENERATOR content="MSHTML 8.00.6001.19222">
<STYLE></STYLE>
</HEAD>
<BODY>
<DIV>
<DIV><FONT size=2 face=Arial>Hello. I am using an AS5400 to generate a PRI that
is then going to a CiscoIAD. So on the AS5400 side I have. The IAD only has 8
analog voice ports, so I am using the last 8 channels of the PRI for voice
ports, and the first 16 channels as a T1 for internet service.</FONT></DIV>
<DIV><FONT size=2 face=Arial></FONT> </DIV>
<DIV><FONT size=2 face="Courier New">controller T1 1/0:24<BR> framing
esf<BR> channel-group 0 timeslots 1-16 speed 64<BR> loopback network
ignore<BR> pri-group timeslots 17-24<BR></FONT></DIV>
<DIV><FONT size=2 face="Courier New">interface Serial1/0:24:0<BR> ip
address 216.24.28.249 255.255.255.252<BR> encapsulation ppp<BR> no cdp
enable<BR>!<BR>interface Serial1/0:24:23<BR> no ip address<BR> isdn
switch-type primary-ni<BR> isdn protocol-emulate network<BR> no isdn
outgoing ie redirecting-number<BR> no isdn incoming alerting
add-PI<BR> no cdp enable<BR></FONT></DIV>
<DIV><FONT size=2 face=Arial></FONT> </DIV>
<DIV><FONT size=2 face=Arial>On the IAD I have....</FONT></DIV>
<DIV><FONT size=2 face=Arial></FONT> </DIV>
<DIV>
<DIV><FONT size=2 face="Courier New">controller T1 1/0</FONT></DIV>
<DIV><FONT size=2 face="Courier New">framing esf</FONT></DIV>
<DIV><FONT size=2 face="Courier New">linecode b8zs</FONT></DIV>
<DIV><FONT size=2 face="Courier New">channel-group 0 timeslots 1-16 speed
64</FONT></DIV>
<DIV><FONT size=2 face="Courier New">pri-group timeslots 17-24 nfas_d primary
nfas_int 1 nfas_group 1</FONT></DIV>
<DIV><FONT size=2 face="Courier New"></FONT> </DIV>
<DIV>
<DIV><FONT size=2 face="Courier New">interface Serial1/0:0</FONT></DIV>
<DIV><FONT size=2 face="Courier New">ip address 216.24.28.250
255.255.255.252</FONT></DIV>
<DIV><FONT size=2 face="Courier New">encapsulation ppp</FONT></DIV>
<DIV><FONT size=2 face="Courier New">!</FONT></DIV>
<DIV><FONT size=2 face="Courier New">interface Serial1/0:23</FONT></DIV>
<DIV><FONT size=2 face="Courier New">no ip address</FONT></DIV>
<DIV><FONT size=2 face="Courier New">isdn switch-type primary-ni</FONT></DIV>
<DIV><FONT size=2 face="Courier New">isdn incoming-voice voice</FONT></DIV>
<DIV><FONT size=2 face="Courier New">no cdp enable</FONT></DIV>
<DIV><FONT size=2 face="Courier New"></FONT> </DIV>
<DIV>
<DIV><FONT size=2 face="Courier New">dial-peer voice 1 pots</FONT></DIV>
<DIV><FONT size=2 face="Courier New">description route calls to
ISDN</FONT></DIV>
<DIV><FONT size=2 face="Courier New">destination-pattern .T</FONT></DIV>
<DIV><FONT size=2 face="Courier New">port 1/0:23</FONT></DIV></DIV></DIV>
<DIV><FONT size=2 face=Arial></FONT> </DIV>
<DIV><FONT size=2 face=Arial>The PRI and TEI's seem to be up. The AS5400 has
intermachine trunks connecting it to the telco system and routes incoming and
outgoing phone calls all day long, but when I try to make an outgoing call from
the Cisco IAD I see the IAD 2400 appear to do the call setup and send the call
out 1/0:23, but eventually I get a reject with a cause code of "0x0",
which isn't very helpful. I'm not even sure if the error message is coming from
the far end (the AS5400) or the near end (the IAD2400).</FONT></DIV>
<DIV><FONT size=2 face=Arial></FONT> </DIV>
<DIV><FONT size=2 face=Arial>Error output below with the reject highlighted in
red. It would seem that the called is being rejected for "Invalid information
element contents." I'm having a hard time determining which elements it
considers invalid, though. We've never generated our own PRI out to a client box
before, so any information anyone has would be greatly appreciated. Also, if
anyone has a config example of both ends of such an arrangement I would love to
see it.</FONT></DIV></DIV></DIV>
<DIV><FONT size=2 face=Arial></FONT> </DIV>
<DIV><FONT size=1 face="Courier New">022127: 1w0d: ISDN Se1/0:24:23 Q931: RX
<- SETUP pd = 8 callref =
0x002C<BR> Bearer Capability i =
0x9090A2<BR>
Standard =
CCITT<BR>
Transer Capability = 3.1kHz
Audio<BR>
Transfer Mode =
Circuit<BR>
Transfer Rate = 64 kbit/s<BR> Channel
ID i =
0xE1818397<BR>
Preferred, Interface 1, Channel 23<BR>
Progress Ind i = 0x8183 - Origination address is
non-ISDN<BR> Calling Party Number i =
0x2183,
'5025673005'<BR>
Plan:ISDN, Type:National<BR> Called
Party Number i = 0x80,
'75023871095'<BR>
Plan:Unknown, Type:Unknown<BR>022128: 1w0d: ISDN Se1/0:24:23 LIFd:
LIF_StartTimer: timer (0x64FBB518), ticks (30000), event (0x1250)<BR>022129:
1w0d: ISDN Se1/0:24:23 Q931d: L3_Go: source = 0x20A, event = 0x241, call id =
0x0, int id = 0x0<BR>022130: 1w0d: ISDN Se1/0:24:23 Q931d: L3_Go: call_id 0x2F62
cr 0x802C state 0 event 0x5 ces 1<BR>022131: 1w0d: ISDN Se1/0:24:23 Q931d:
L3_ProcessEvent: callref = 0x802C SETUP:U0_Setup(nlcb)<BR>022132: 1w0d: ISDN
Se1/0:24:23 Q931d: L3_state_change: callref 0x802C old NULL_STATE, new
CALL_PRESENT<BR>022133: 1w0d: ISDN Se1/0:24:23 Q931d: L3_Go: source = 0x400,
event = 0x340, call id = 0x2F62, int id = 0x0<BR>022134: 1w0d: ISDN Se1/0:24:23
Q931d: L3_Go: call_id 0x2F62 cr 0x802C state 6 event 0x82 ces 1<BR>022135: 1w0d:
ISDN Se1/0:24:23 Q931d: L3_ProcessEvent: callref = 0x802C
CC_SETUP_REJ_REQ:U6_SetupRejReq(nlcb)<BR>022136: 1w0d: ISDN Se1/0:24:23 Q931d:
L3_state_change: callref 0x802C old CALL_PRESENT, new NULL_STATE<BR>022137:
1w0d: ISDN Se1/0:24:23 LIFd: LIF_StartTimer: timer (0x65F432AC), ticks (1000),
event (0x1240)<BR><FONT color=#ff0000>022138: 1w0d: ISDN Se1/0:24:23 Q931: TX
-> RELEASE_COMP pd = 8 callref =
0x802C<BR> Cause i = 0x82E418 -
Invalid information element contents<BR></FONT>022139: 1w0d: ISDN Se1/0:24:23
LIFd: LIF_StartTimer: timer (0x64FBB518), ticks (30000), event
(0x1250)<BR>AMSS1#<BR></FONT></DIV></BODY></HTML>