[nsp] Fastethernet fatal hardware error
Daniel Cuautle
dcuautle@adetel.net
Wed, 13 Nov 2002 15:55:51 -0600
I don't have memory to change it. This is new card.
The problem is present every time.
Thanks
DC
"Steven W. Raymond" wrote:
> Crash looks to be to be caused by a parity error in the packet memory
> SRAM component:
> 1d06h: %FEIP2-1-MSG: slot6 PMA error register = 0280003000000000
> ...
> 1d06h: %FEIP2-1-MSG: slot6 Detected Parity Error on secondary
> bus
>
> Can you try swapping out the SRAM? It's the large 4" by say 6" memory
> component, attached with 3 screws and is usually 4MB or 8MB for VIP2-50
> based IPs.
> Did this error happen only once or every time you try to bring up the
> router?
>
> Daniel Cuautle wrote:
> >
> > Someone can help me?
> >
> > I installed new card on 7507 box, but have troubles. I was restart mi router
> > cisco 7507, IOS 12.1(6)E.
> >
> > Can save this card?
> >
> > Thanks in advance
> > DC
> >
> > 0000000000000000000000000000000000000000000000000000000000000000
> > 1d06h: %LINK-3-UPDOWN: Interface FastEthernet6/0/0, changed state to down
> > 1d06h: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet6/0/0, changn
> >
> > 1d06h: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet4/1, changed stap
> >
> > 1d06h: %FEIP2-1-MSG: slot6 PCI bus 0 system error
> > 1d06h: %FEIP2-1-MSG: slot6 PMA error register = 0280003000000000
> > 1d06h: %FEIP2-1-MSG: slot6 PCI master address = 2800030
> > 1d06h: %FEIP2-1-MSG: slot6 PA Bay 0 Upstream PCI-PCI Bridge, Handle=0
> > 1d06h: %FEIP2-1-MSG: slot6 DEC21050 bridge chip, config=0x0
> > 1d06h: %FEIP2-1-MSG: slot6 (0x00):dev, vendor id = 0x00011011
> > 1d06h: %FEIP2-1-MSG: slot6 (0x04):status, command = 0x02800147
> > 1d06h: %FEIP2-1-MSG: slot6 (0x08):class code, revid = 0x06040002
> > 1d06h: %FEIP2-1-MSG: slot6 (0x0C):hdr, lat timer, cls = 0x00010000
> > 1d06h: %FEIP2-1-MSG: slot6 (0x18):sec lat,cls & bus no = 0x08010100
> > 1d06h: %FEIP2-1-MSG: slot6 (0x1C):sec status, io base = 0x22807020
> > 1d06h: %FEIP2-1-MSG: slot6 Received Master Abort on secondary bus
> > 1d06h: %FEIP2-1-MSG: slot6 (0x20):mem base & limit = 0x01F00000
> > 1d06h: %FEIP2-1-MSG: slot6 (0x24):prefetch membase/lim = 0x0000FE00
> > 1d06h: %FEIP2-1-MSG: slot6 (0x3C):bridge ctrl = 0x00030000
> > 1d06h: %FEIP2-1-MSG: slot6 (0x40):arb/serr, chip ctrl = 0x00100000
> > 1d06h: %FEIP2-1-MSG: slot6 (0x44):pri/sec trgt wait t. = 0x00000000
> > 1d06h: %FEIP2-1-MSG: slot6 (0x48):sec write attmp ctr = 0x00FFFFFF
> > 1d06h: %FEIP2-1-MSG: slot6 (0x4C):pri write attmp ctr = 0x00FFFFFF
> > 1d06h: %FEIP2-1-MSG: slot6 PA Bay 1 Upstream PCI-PCI Bridge, Handle=1
> > 1d06h: %FEIP2-1-MSG: slot6 DEC21050 bridge chip, config=0x0
> > 1d06h: %FEIP2-1-MSG: slot6 (0x00):dev, vendor id = 0x00011011
> > 1d06h: %FEIP2-1-MSG: slot6 (0x04):status, command = 0x62800147
> > 1d06h: %FEIP2-1-MSG: slot6 Signaled System Error on primary bus
> > 1d06h: %FEIP2-1-MSG: slot6 Received Master Abort on primary bus
> > 1d06h: %FEIP2-1-MSG: slot6 (0x08):class code, revid = 0x06040002
> > 1d06h: %FEIP2-1-MSG: slot6 (0x0C):hdr, lat timer, cls = 0x00010000
> > 1d06h: %FEIP2-1-MSG: slot6 (0x18):sec lat,cls & bus no = 0x08020200
> > 1d06h: %FEIP2-1-MSG: slot6 (0x1C):sec status, io base = 0xA280F0A0
> > 1d06h: %FEIP2-1-MSG: slot6 Detected Parity Error on secondary bus
> > 1d06h: %FEIP2-1-MSG: slot6 Received Master Abort on secondary bus
> > 1d06h: %FEIP2-1-MSG: slot6 (0x20):mem base & limit = 0x03F00200
> > 1d06h: %FEIP2-1-MSG: slot6 (0x24):prefetch membase/lim = 0x0000FE00
> > 1d06h: %FEIP2-1-MSG: slot6 (0x3C):bridge ctrl = 0x00030000
> > 1d06h: %FEIP2-1-MSG: slot6 (0x40):arb/serr, chip ctrl = 0x00100000
> > 1d06h: %FEIP2-1-MSG: slot6 (0x44):pri/sec trgt wait t. = 0x00000000
> > 1d06h: %FEIP2-1-MSG: slot6 (0x48):sec write attmp ctr = 0x00FFFFFF
> > 1d06h: %FEIP2-1-MSG: slot6 (0x4C):pri write attmp ctr = 0x00FFFFFFUnable to op.
> >
> > 1d06h: %FEIP2-1-MSG: slot6 System reloaded by a fatal hardware error
> > 1d06h: %FEIP2-1-MSG: slot6 caller=0x600E90FC
> > 1d06h: %FEIP2-1-MSG: slot6 System exception: sig=22, code=0x0, context=0x607A078
> >
> > 1d06h: %FEIP2-1-MSG: slot6 $0 : 00000000, AT : 606B0000, v0 : 4800AFF0, v1 : 60,
> >
> > 1d06h: %FEIP2-1-MSG: slot6 a0 : 48000130, a1 : 00004000, a2 : 000000F8, a3 : 00,
> >
> > 1d06h: %FEIP2-1-MSG: slot6 t0 : 00000010, t1 : 00000010, t2 : 00000000, t3 : FF,
> >
> > 1d06h: %FEIP2-1-MSG: slot6 t4 : 600E9138, t5 : 000000F8, t6 : 00000000, t7 : 00,
> >
> > 1d06h: %FEIP2-1-MSG: slot6 s0 : 60985380, s1 : 00004000, s2 : 6072EBEC, s3 : 60.
> >
> > 1d06h: %FEIP2-1-MSG: slot6 s4 : 60985380, s5 : 605A0000, s6 : 60730000, s7 : 60,
> >
> > 1d06h: %FEIP2-1-MSG: slot6 t8 : 60760000, t9 : 00000000, k0 : 608E1EA0, k1 : 60,
> >
> > 1d06h: %FEIP2-1-MSG: slot6 gp : 606BEFC0, sp : 608EC8F0, s8 : 00000000, ra : 60,
> >
> > 1d06h: %FEIP2-1-MSG: slot6 EPC : 6026B720, ErrorEPC : 80008618, SREG : 3400C103
> > 1d06h: %FEIP2-1-MSG: slot6 Cause 00000000 (Code 0x0)
> > 1d06h: %FEIP2-1-MSG: slot6 Traceback= 6026B720 6026DE3C 6026D208 6026D35C 60141D
> >
> > 1d06h: %FEIP2-1-MSG: slot6 C 600BF2C8
> > 1d06h: %DBUS-3-DBUSINTERRSWSET: Slot 6, Internal Error due to VIP crash
> > 1d06h: %RSP-3-RESTART: cbus complex
> > 1d06h: %CONTROLLER-5-UPDOWN: Controller E1 0/1/0, changed state to up
> > 1d06h: %CONTROLLER-5-UPDOWN: Controller E1 0/1/1, changed state to up
> > 1d06h: %CONTROLLER-5-UPDOWN: Controller E1 1/1, changed state to up
> > 1d06h: %CONTROLLER-5-UPDOWN: Controller E1 1/0, changed state to up
> > 1d06h: %FEIP2-1-MSG: slot6 PCI bus 0 system error
> > 1d06h: %FEIP2-1-MSG: slot6 PMA error register = 0280003800000000
> > 1d06h: %FEIP2-1-MSG: slot6 PCI master address = 2800038
> > 1d06h: %FEIP2-1-MSG: slot6 PA Bay 0 Upstream PCI-PCI Bridge, Handle=0
> > 1d06h: %FEIP2-1-MSG: slot6 DEC21050 bridge chip, config=0x0
> > 1d06h: %FEIP2-1-MSG: slot6 (0x00):dev, vendor id = 0x00011011
> > 1d06h: %FEIP2-1-MSG: slot6 (0x04):status, command = 0x02800147
> > 1d06h: %FEIP2-1-MSG: slot6 (0x08):class code, revid = 0x06040002
> > 1d06h: %FEIP2-1-MSG: slot6 (0x0C):hdr, lat timer, cls = 0x00010000
> > 1d06h: %FEIP2-1-MSG: slot6 (0x18):sec lat,cls & bus no = 0x08010100
> > 1d06h: %FEIP2-1-MSG: slot6 (0x1C):sec status, io base = 0x22807020
> > 1d06h: %FEIP2-1-MSG: slot6 Received Master Abort on secondary bus
> > 1d06h: %FEIP2-1-MSG: slot6 (0x20):mem base & limit = 0x01F00000
> > 1d06h: %FEIP2-1-MSG: slot6 (0x24):prefetch membase/lim = 0x0000FE00
> > 1d06h: %FEIP2-1-MSG: slot6 (0x3C):bridge ctrl = 0
> > x00030000
> > 1d06h: %FEIP2-1-MSG: slot6 (0x40):arb/serr, chip ctrl = 0x00100000
> > 1d06h: %FEIP2-1-MSG: slot6 (0x44):pri/sec trgt wait t. = 0x00000000
> > 1d06h: %FEIP2-1-MSG: slot6 (0x48):sec write attmp ctr = 0x00FFFFFF
> > 1d06h: %FEIP2-1-MSG: slot6 (0x4C):pri write attmp ctr = 0x00FFFFFF
> > 1d06h: %FEIP2-1-MSG: slot6 PA Bay 1 Upstream PCI-PCI Bridge, Handle=1
> > 1d06h: %FEIP2-1-MSG: slot6 DEC21050 bridge chip, config=0x0
> > 1d06h: %FEIP2-1-MSG: slot6 (0x00):dev, vendor id = 0x00011011
> > 1d06h: %FEIP2-1-MSG: slot6 (0x04):status, command = 0x42800147
> > 1d06h: %FEIP2-1-MSG: slot6 Signaled System Error on primary bus
> > 1d06h: %FEIP2-1-MSG: slot6 (0x08):class code, revid = 0x06040002
> > 1d06h: %FEIP2-1-MSG: slot6 (0x0C):hdr, lat timer, cls = 0x00010000
> > 1d06h: %FEIP2-1-MSG: slot6 (0x18):sec lat,cls & bus no = 0x08020200
> > 1d06h: %FEIP2-1-MSG: slot6 (0x1C):sec status, io base = 0x8280F0A0
> > 1d06h: %FEIP2-1-MSG: slot6 Detected Parity Error on secondary bus
> > 1d06h: %FEIP2-1-MSG: slot6 (0x20):mem base & limit = 0x03F00200
> > 1d06h: %FEIP2-1-MSG: slot6 (0x24):prefetch membase/lim = 0x0000FE00
> > 1d06h: %FEIP2-1-MSG: slot6 (0x3C):bridge ctrl = 0x00030000
> > 1d06h: %FEIP2-1-MSG: slot6 (0x40):arb/serr, chip ctrl = 0x00100000
> > 1d06h: %FEIP2-1-MSG: slot6 (0x44):pri/sec trgt wait t. = 0x00000000
> > 1d06h: %FEIP2-1-MSG: slot6 (0x48):sec write attmp ctr = 0x00FFFFFF
> > 1d06h: %FEIP2-1-MSG: slot6 (0x4C):pri write attmp ctr = 0x00FFFFFFUnable to op.
> >
> > el#
> > el#
> > 1d06h: %FEIP2-1-MSG: slot6 System reloaded by a fatal hardware error
> > 1d06h: %FEIP2-1-MSG: slot6 caller=0x600E90FC
> > 1d06h: %FEIP2-1-MSG: slot6 System exception: sig=22, code=0x0, context=0x607A078
> >
> > 1d06h: %FEIP2-1-MSG: slot6 $0 : 00000000, AT : 606B0000, v0 : 0000C318, v1 : 52,
> >
> > 1d06h: %FEIP2-1-MSG: slot6 a0 : 811C73CC, a1 : 000003E8, a2 : 000003E8, a3 : 00,
> >
> > 1d06h: %FEIP2-1-MSG: slot6 t0 : 000F4240, t1 : 00000010, t2 : 00000000, t3 : FF,
> >
> > 1d06h: %FEIP2-1-MSG: slot6 t4 : 000000F8, t5 : 000000F8, t6 : 00000000, t7 : 00,
> >
> > 1d06h: %FEIP2-1-MSG: slot6 s0 : 00000001, s1 : 00000010, s2 : 60985380, s3 : 60,
> >
> > 1d06h: %FEIP2-1-MSG: slot6 s4 : 60985380, s5 : 00000000, s6 : 00000000, s7 : 00,
> >
> > 1d06h: %FEIP2-1-MSG: slot6 t8 : 60760000, t9 : 00000000, k0 : 608E1EA0, k1 : 60,
> >
> > 1d06h: %FEIP2-1-MSG: slot6 gp : 606BEFC0, sp : 608EC908, s8 : 00000000, ra : 60,
> >
> > 1d06h: %FEIP2-1-MSG: slot6 EPC : 600E7F74, ErrorEPC : 80008618, SREG : 3400C103
> > 1d06h: %FEIP2U-1-MSG: slot6 Cause 80000000 (Code 0x0)
> > 1d06h: %FEIP2-1-MSG: slot6 Traceback= 600E7F78 600E7E00 60141CF0 60143AF0 60140C
> >
> > 1d06h: %FEIP2-1-MSG: slot6 8 nable to open file, crashinfo packet dropped.
> > Unable to open file, crashinfo packet dropped.
> >
> > _______________________________________________
> > cisco-nsp mailing list real_name)s@puck.nether.net
> > http://puck.nether.net/mailman/listinfo/cisco-nsp
> > archive at http://puck.nether.net/pipermail/cisco-nsp/