[nsp] 12.2.2XB8 line/modem/controller-t1 numbering

[Brian Roberson]

they do,but dnis is not provisioned on the circuits.


----- Original Message -----
From: "Josh Duffek" <jduffek@cisco.com>
To: "Brian Roberson" <roberson@olug.org>; <cisco-nsp@puck.nether.net>
Sent: Monday, November 25, 2002 6:11 PM
Subject: Re: [nsp] 12.2.2XB8 line/modem/controller-t1 numbering


> do the t1s have different phone numbers?  if so you can use RPM:
>
http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/120newft/120
> limit/120xi/rpm4xi1.htm
>
> joshd.
>
> ----- Original Message -----
> From: "Brian Roberson" <roberson@olug.org>
> To: <cisco-nsp@puck.nether.net>
> Sent: Monday, November 25, 2002 6:09 PM
> Subject: [nsp] 12.2.2XB8 line/modem/controller-t1 numbering
>
>
> as5300, two CAS t1's
> how can I ensure calls on controller 0 only use tty lines 1-24 ; and
> controller 1 use tty lines 25-48?
>
> example config:
>
> ...
> !
> controller T1 0
>  framing esf
>  linecode b8zs
>  ds0-group 0 timeslots 1-24 type e&m-fgb dtmf dnis
>  description T1-1
> !
> controller T1 1
>  framing esf
>  linecode b8zs
>  ds0-group 1 timeslots 1-24 type e&m-fgb dtmf dnis
>  description T1-2
> !
> ....
> line 1 24
>  exec-timeout 0 0
>  modem Dialin
>  modem autoconfigure type mica
>  autocommand  telnet HOST1 PORT1 /quiet /stream
>  terminal-type vt100
>  exec-character-bits 8
>  length 80
>  escape-character NONE
>  telnet transparent
> line 25 48
>  exec-timeout 0 0
>  modem Dialin
>  modem autoconfigure type pdx
>  autocommand  telnet HOST2 PORT2 /stream /quiet
>  terminal-type vt100
>  exec-character-bits 8
>  length 80
>  escape-character NONE
>  telnet transparent
> !
> !
>
>
>
>
>
> What I would expect is lines 1-24 would be controller t1 0 and 25-48 would
> controller t1 1, this is not necisarily the case.
>
>
> oma-async01#sh line 1
>    Tty Typ     Tx/Rx    A Modem  Roty AccO AccI   Uses   Noise  Overruns
> Int
>      1 TTY              - DialIn    -    -    -      0       0
> 0       -
>
> Line 1, Location: "", Type: "vt100"
> Length: 80 lines, Width: 80 columns
> Status: No Exit Banner, Modem Detected, CTS Raised
> Capabilities: Telnet Transparent Mode, Hardware Flowcontrol In
>   Hardware Flowcontrol Out, Modem RI is CD, Modem Autoconfigure
>   Integrated Modem
> Modem state: Idle
>   modem(slot/port)=1/0, state=IDLE
>   dsx1(slot/unit/channel)=NONE, status=VDEV_STATUS_UNLOCKED
> Modem hardware state: CTS noDSR  DTR RTS, Modem Configured
> Special Chars: Escape  Hold  Stop  Start  Disconnect  Activation
>                 none   none   -     -       none
> Timeouts:      Idle EXEC    Idle Session   Modem Answer  Session
Dispatch
>                 never         never                        none     not
set
>                             Idle Session Disconnect Warning
>                               never
>                             Login-sequence User Response
>                              00:00:30
>                             Autoselect Initial Wait
>                               not set
> Modem type is pdx.
> Session limit is not set.
> Time since activation: never
> Editing is enabled.
> History is enabled, history size is 10.
> DNS resolution in show commands is enabled
> Full user help is disabled
> Allowed input transports are none.
> Allowed output transports are pad telnet rlogin.
> Preferred transport is telnet.
> Automatically execute command "telnet HOST1 PORT1 /stream /quiet"
> No output characters are padded
> No special data dispatching characters
> router#
>
>
>
>
>
>
>
>
> ......
>