[nsp] %DSX1-3-M32_MEM_ALLOC help

[Vicky Mair]

hi there,

just doing sanity check on the following issue which my customer is running
into. according to the error message decoder it appears to be a low memory
issue. what baffles me is that i have no config on this box and when i try
and change the config on this box i get malloc messages (see below). not
sure if this  has to do with the packet memory, dram or what.....but any
insight in this matter will be appreciated.

tia,
/vicky



5300-ir1#sh ver
Cisco Internetwork Operating System Software
IOS (tm) 5300 Software (C5300-JS-M), Version 12.2(13)T,  RELEASE SOFTWARE
(fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Sat 16-Nov-02 04:04 by ccai
Image text-base: 0x60008938, data-base: 0x616DC000

ROM: System Bootstrap, Version 11.2(9)XA, RELEASE SOFTWARE (fc2)
BOOTLDR: 5300 Software (C5300-BOOT-M), Version 12.2(13)T,  RELEASE SOFTWARE
(fc1)

5300-ir1 uptime is 0 minutes
System returned to ROM by power-on
System image file is "flash:c5300-js-mz.122-13.T.bin"

cisco AS5300 (R4K) processor (revision A.32) with 131072K/4096K bytes of
memory.
Processor board ID 10081036
R4700 CPU at 150Mhz, Implementation 33, Rev 1.0, 512KB L2 Cache
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
Primary Rate ISDN software, Version 1.1.
Backplane revision 2
Manufacture Cookie Info:
 EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x30,
 Board Hardware Version 1.64, Item Number 800-2544-02,
 Board Revision B0, Serial Number 10081036,
 PLD/ISP Version 0.0,  Manufacture Date 14-Oct-1998.
1 Ethernet/IEEE 802.3 interface(s)
1 FastEthernet/IEEE 802.3 interface(s)
4 Channelized T1/PRI port(s)
128K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
8192K bytes of processor board Boot flash (Read/Write)

Configuration register is 0x2102



5300-ir1(config-controller)#pri-group timeslots 1-24
00:01:56: %LINK-5-CHANGED: Interface Serial0:23, changed state to reset
5300-ir1(config-controller)#
5300-ir1(config-controller)#cont t1 1
5300-ir1(config-controller)#pri-group timeslots 1-24
5300-ir1(config-controller)#
5300-ir1(config-controller)#
00:02:18: %LINK-5-CHANGED: Interface Serial1:23, changed state to resetcont
t1 2
5300-ir1(config-controller)#pri-group timeslots 1-24
5300-ir1(config-controller)#

00:02:29: %SYS-2-MALLOCFAIL: Memory allocation of 1680 bytes failed from
0x6031A53C, alignment 0
Pool: I/O  Free: 2592  Cause: Memory fragmentation
Alternate Pool: None  Free: 0  Cause: No Alternate pool

-Process= "Exec", ipl= 5, pid= 80
-Traceback= 60376424 60377084 6031A544 60384D7C 600264A0 60026C7C 60025270
6001A128 6001D2F8 602E7010 602F9CD4 6036B164 6036B150
00:02:29: %DSX1-3-M32_MEM_ALLOC: Munich 32 channel memory allocation error:
Ctrl = 0x3C400040, Channel = 5
-Process= "Exec", ipl= 3, pid= 80
-Traceback= 6000C23C 60026CB4 60027058 600252D8 60025448 60544990 6053BCA8
60025B7C 6001A064 6001D2F8 602E7010 602F9CD4 6036B164 603
6B150
00:02:29: %DSX1-3-M32_MEM_ALLOC: Munich 32 channel memory allocation error:
Ctrl = 0x3C400040, Channel = 5
-Process= "Exec", ipl= 3, pid= 80
-Traceback= 6000C23C 60026CB4 60025270 6001A128 6001D2F8 602E7010 602F9CD4
6036B164 6036B150
00:02:29: %DSX1-3-M32_MEM_ALLOC: Munich 32 channel memory allocation error:
Ctrl = 0x3C400040, Channel = 6
-Process= "Exec", ipl= 3, pid= 80
-Traceback= 6000C23C 60026CB4 60027058 600252D8 60025448 60544990 6053BCA8
60025B7C 6001A064 6001D2F8 602E7010 602F9CD4 6036B164 603
6B150