[nsp] %DSX1-3-M32_MEM_ALLOC help
Oliver Boehmer (oboehmer)
oboehmer at cisco.com
Fri Jan 31 08:59:10 EST 2003
Vicky,
are you using the as5300 for voice or dial? If you're doing the latter,
please use 12.2(2)XB10 instead, 12.2(13)T is not recommended for dial on
AS5xxx platforms.
oli
> -----Original Message-----
> From: Vicky Mair [mailto:vickyr at socal.rr.com]
> Sent: Donnerstag, 30. Januar 2003 19:34
> To: Stephen J. Wilcox
> Cc: cisco-nsp at puck.nether.net
> Subject: RE: [nsp] %DSX1-3-M32_MEM_ALLOC help
>
>
> the image requires minimum of 128/16 dram/flash which i have and
> unfortunately this particular box can do a maximum of 128mb
> dram...maybe i
> am trying to push this box than it can handle.
>
>
>
> /vicky
>
> -----Original Message-----
> From: cisco-nsp-bounces at puck.nether.net
> [mailto:cisco-nsp-bounces at puck.nether.net]On Behalf Of
> Stephen J. Wilcox
> Sent: Thursday, January 30, 2003 10:14 AM
> To: Vicky Mair
> Cc: cisco-nsp at puck.nether.net
> Subject: Re: [nsp] %DSX1-3-M32_MEM_ALLOC help
>
>
>
> Just reading the messages without doing any digging I'd say
> the box doesnt
> have
> enough memory to support the IOS you have.
>
> Even without config it still uses memory to run all the basic
> processes..
>
> Have you checked cisco.com for minimum memory on this
> platform and IOS?
>
> Steve
>
> On Thu, 30 Jan 2003, Vicky Mair wrote:
>
> > hi there,
> >
> > just doing sanity check on the following issue which my customer is
> running
> > into. according to the error message decoder it appears to
> be a low memory
> > issue. what baffles me is that i have no config on this box
> and when i try
> > and change the config on this box i get malloc messages
> (see below). not
> > sure if this has to do with the packet memory, dram or
> what.....but any
> > insight in this matter will be appreciated.
> >
> > tia,
> > /vicky
> >
> >
> >
> > 5300-ir1#sh ver
> > Cisco Internetwork Operating System Software
> > IOS (tm) 5300 Software (C5300-JS-M), Version 12.2(13)T,
> RELEASE SOFTWARE
> > (fc1)
> > TAC Support: http://www.cisco.com/tac
> > Copyright (c) 1986-2002 by cisco Systems, Inc.
> > Compiled Sat 16-Nov-02 04:04 by ccai
> > Image text-base: 0x60008938, data-base: 0x616DC000
> >
> > ROM: System Bootstrap, Version 11.2(9)XA, RELEASE SOFTWARE (fc2)
> > BOOTLDR: 5300 Software (C5300-BOOT-M), Version 12.2(13)T, RELEASE
> SOFTWARE
> > (fc1)
> >
> > 5300-ir1 uptime is 0 minutes
> > System returned to ROM by power-on
> > System image file is "flash:c5300-js-mz.122-13.T.bin"
> >
> > cisco AS5300 (R4K) processor (revision A.32) with
> 131072K/4096K bytes of
> > memory.
> > Processor board ID 10081036
> > R4700 CPU at 150Mhz, Implementation 33, Rev 1.0, 512KB L2 Cache
> > Bridging software.
> > X.25 software, Version 3.0.0.
> > SuperLAT software (copyright 1990 by Meridian Technology Corp).
> > TN3270 Emulation software.
> > Primary Rate ISDN software, Version 1.1.
> > Backplane revision 2
> > Manufacture Cookie Info:
> > EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x30,
> > Board Hardware Version 1.64, Item Number 800-2544-02,
> > Board Revision B0, Serial Number 10081036,
> > PLD/ISP Version 0.0, Manufacture Date 14-Oct-1998.
> > 1 Ethernet/IEEE 802.3 interface(s)
> > 1 FastEthernet/IEEE 802.3 interface(s)
> > 4 Channelized T1/PRI port(s)
> > 128K bytes of non-volatile configuration memory.
> > 16384K bytes of processor board System flash (Read/Write)
> > 8192K bytes of processor board Boot flash (Read/Write)
> >
> > Configuration register is 0x2102
> >
> >
> >
> > 5300-ir1(config-controller)#pri-group timeslots 1-24
> > 00:01:56: %LINK-5-CHANGED: Interface Serial0:23, changed
> state to reset
> > 5300-ir1(config-controller)#
> > 5300-ir1(config-controller)#cont t1 1
> > 5300-ir1(config-controller)#pri-group timeslots 1-24
> > 5300-ir1(config-controller)#
> > 5300-ir1(config-controller)#
> > 00:02:18: %LINK-5-CHANGED: Interface Serial1:23, changed state to
> resetcont
> > t1 2
> > 5300-ir1(config-controller)#pri-group timeslots 1-24
> > 5300-ir1(config-controller)#
> >
> > 00:02:29: %SYS-2-MALLOCFAIL: Memory allocation of 1680
> bytes failed from
> > 0x6031A53C, alignment 0
> > Pool: I/O Free: 2592 Cause: Memory fragmentation
> > Alternate Pool: None Free: 0 Cause: No Alternate pool
> >
> > -Process= "Exec", ipl= 5, pid= 80
> > -Traceback= 60376424 60377084 6031A544 60384D7C 600264A0
> 60026C7C 60025270
> > 6001A128 6001D2F8 602E7010 602F9CD4 6036B164 6036B150
> > 00:02:29: %DSX1-3-M32_MEM_ALLOC: Munich 32 channel memory allocation
> error:
> > Ctrl = 0x3C400040, Channel = 5
> > -Process= "Exec", ipl= 3, pid= 80
> > -Traceback= 6000C23C 60026CB4 60027058 600252D8 60025448
> 60544990 6053BCA8
> > 60025B7C 6001A064 6001D2F8 602E7010 602F9CD4 6036B164 603
> > 6B150
> > 00:02:29: %DSX1-3-M32_MEM_ALLOC: Munich 32 channel memory allocation
> error:
> > Ctrl = 0x3C400040, Channel = 5
> > -Process= "Exec", ipl= 3, pid= 80
> > -Traceback= 6000C23C 60026CB4 60025270 6001A128 6001D2F8
> 602E7010 602F9CD4
> > 6036B164 6036B150
> > 00:02:29: %DSX1-3-M32_MEM_ALLOC: Munich 32 channel memory allocation
> error:
> > Ctrl = 0x3C400040, Channel = 6
> > -Process= "Exec", ipl= 3, pid= 80
> > -Traceback= 6000C23C 60026CB4 60027058 600252D8 60025448
> 60544990 6053BCA8
> > 60025B7C 6001A064 6001D2F8 602E7010 602F9CD4 6036B164 603
> > 6B150
> >
> >
> > _______________________________________________
> > cisco-nsp mailing list cisco-nsp at puck.nether.net
> > http://puck.nether.net/mailman/listinfo/cisco-nsp
> > archive at http://puck.nether.net/pipermail/cisco-nsp/
> >
>
> _______________________________________________
> cisco-nsp mailing list cisco-nsp at puck.nether.net
> http://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/
>
>
> _______________________________________________
> cisco-nsp mailing list cisco-nsp at puck.nether.net
> http://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/
>
More information about the cisco-nsp
mailing list