[nsp] Multiple OSPF routing on a C6400 NRP1?
Clayton Zekelman
clayton at MNSi.Net
Mon Jul 28 17:51:40 EDT 2003
I feel like a total weenie.
That makes complete sense. The 7200 we were migrating from had lots of
interfaces for the OSPF tasks to grab IP's from.
I guess the part that threw me was the fact that the command parser
wouldn't even take the config.
MUCH appreciated.
At 12:56 PM 28/07/2003 -0700, you wrote:
>Thanks Clayton.
>
>I turned on "term mon" and saw this:
>
>uacA5-Windsor#term mon
>uacA5-Windsor#conf t
>Enter configuration commands, one per line. End with CNTL/Z.
>uacA5-Windsor(config)#router ospf 2
>Jul 28 19:47:03.847: %OSPF-4-NORTRID: OSPF process 2 cannot start. There
must be at least one "up" IP interface, for OSPF to use as router ID
>
>It looks like the 2nd OSPF process needs to choose a different router
>id then the first process. Since only one IP address is configured on
>the box, the process failed to start.
>
>I configured a loopback and stuck an IP on it and now it seems ok. :)
>
>Dennis
>
>uacA5-Windsor(config)#int lo0
>uacA5-Windsor(config-if)#ip address 10.1.1.1 255.255.255.0
>uacA5-Windsor(config-if)#exit
>uacA5-Windsor(config)#router ospf 2
>uacA5-Windsor(config-router)#^Z
>uacA5-Windsor#sh ip ospf
> Routing Process "ospf 2" with ID 10.1.1.1
> Supports only single TOS(TOS0) routes
> Supports opaque LSA
> Supports Link-local Signaling (LLS)
> Initial SPF schedule delay 5000 msecs
> Minimum hold time between two consecutive SPFs 10000 msecs
> Maximum wait time between two consecutive SPFs 10000 msecs
> Minimum LSA interval 5 secs. Minimum LSA arrival 1 secs
> LSA group pacing timer 240 secs
> Interface flood pacing timer 33 msecs
> Retransmission pacing timer 66 msecs
> Number of external LSA 0. Checksum Sum 0x000000
> Number of opaque AS LSA 0. Checksum Sum 0x000000
> Number of DCbitless external and opaque AS LSA 0
> Number of DoNotAge external and opaque AS LSA 0
> Number of areas in this router is 0. 0 normal 0 stub 0 nssa
> External flood list length 0
>
> Routing Process "ospf 1" with ID 216.8.137.198
> Supports only single TOS(TOS0) routes
> Supports opaque LSA
> Supports Link-local Signaling (LLS)
> It is an autonomous system boundary router
> Redistributing External Routes from,
> connected, includes subnets in redistribution
> static, includes subnets in redistribution
> Initial SPF schedule delay 5000 msecs
> Minimum hold time between two consecutive SPFs 10000 msecs
> Maximum wait time between two consecutive SPFs 10000 msecs
> Minimum LSA interval 5 secs. Minimum LSA arrival 1 secs
> LSA group pacing timer 240 secs
> Interface flood pacing timer 33 msecs
> Retransmission pacing timer 66 msecs
> Number of external LSA 430. Checksum Sum 0xD475D7
> Number of opaque AS LSA 0. Checksum Sum 0x000000
> Number of DCbitless external and opaque AS LSA 47
> Number of DoNotAge external and opaque AS LSA 0
> Number of areas in this router is 1. 1 normal 0 stub 0 nssa
> External flood list length 0
> Area BACKBONE(0)
> Number of interfaces in this area is 2
> Area has no authentication
> SPF algorithm last executed 02:02:05.648 ago
> SPF algorithm executed 3 times
> Area ranges are
> Number of LSA 25. Checksum Sum 0x0DAC78
> Number of opaque link LSA 0. Checksum Sum 0x000000
> Number of DCbitless LSA 7
> Number of indication LSA 0
> Number of DoNotAge LSA 0
> Flood list length 0
>
>
>Clayton Zekelman [clayton at mnsi.net] wrote:
>> Whoops - with OSPF down it wasn't seeing a gateway. I just statically
>> routed it.
>>
>> You can reach it at uaca5.win.mnsi.net (216.8.137.198)
>>
>> At 12:21 PM 28/07/2003 -0700, you wrote:
>> >Thanks. Used your exact config and still no luck on reproducing this at
>> >my end. Could I get remote access into this box?
>> >
>> >Dennis
>> >
>> >Clayton Zekelman [clayton at mnsi.net] wrote:
>> >> Here it is. I tried it with 12.3(1a) also. Same results.
>> >>
>> >>
>> >> Cisco Internetwork Operating System Software
>> >> IOS (tm) C6400R Software (C6400R-G4P5-M), Version 12.2(15)T5, RELEASE
>> >> SOFTWARE
>> >> (fc1)
>> >> TAC Support: http://www.cisco.com/tac
>> >> Copyright (c) 1986-2003 by cisco Systems, Inc.
>> >> Compiled Thu 12-Jun-03 05:47 by eaarmas
>> >> Image text-base: 0x60008954, data-base: 0x61222000
>> >>
>> >> ROM: System Bootstrap, Version 11.3(5)DB2, EARLY DEPLOYMENT RELEASE
>> >> SOFTWARE (fc
>> >> 1)
>> >>
>> >> uacA5-Windsor uptime is 1 day, 21 hours, 19 minutes
>> >> uacA5-Windsor uptime since becoming master is 1 day, 21 hours, 19
minutes
>> >> System returned to ROM by reload at 21:06:04 UTC Sat Jul 26 2003
>> >> System restarted at 21:06:25 UTC Sat Jul 26 2003
>> >> System image file is "flash:c6400r-g4p5-mz.122-15.T5.bin"
>> >>
>> >> cisco NRP (NRP1) processor with 94208K/36864K bytes of memory.
>> >> R5000 CPU at 200Mhz, Implementation 35, Rev 2.1, 1024KB L2 Cache
>> >> Last reset from s/w warm reset
>> >> X.25 software, Version 3.0.0.
>> >> Bridging software.
>> >> 2 Ethernet/IEEE 802.3 interface(s)
>> >> 1 FastEthernet/IEEE 802.3 interface(s)
>> >> 1 ATM network interface(s)
>> >> 125K bytes of non-volatile configuration memory.
>> >>
>> >> 4096K bytes of Boot flash ROM (Sector size 256K).
>> >> 16384K bytes of Flash SIMM (Sector size 256K).
>> >> Configuration register is 0x2102
>> >>
>> >> uacA5-Windsor#show run
>> >> Building configuration...
>> >>
>> >> Current configuration : 3562 bytes
>> >> !
>> >> ! Last configuration change at 18:01:25 UTC Mon Jul 28 2003
>> >> ! NVRAM config last updated at 17:47:02 UTC Mon Jul 28 2003
>> >> !
>> >> version 12.2
>> >> service timestamps debug datetime msec
>> >> service timestamps log datetime msec
>> >> no service password-encryption
>> >> !
>> >> hostname uacA5-Windsor
>> >> !
>> >> logging queue-limit 100
>> >> logging buffered 131072 debugging
>> >> no logging console
>> >> enable secret 5 $1$M95t$BUTeOd.eddt2ZFqonAVHJ1
>> >> !
>> >> redundancy
>> >> main-cpu
>> >> auto-sync standard
>> >> no secondary console enable
>> >> !
>> >> !
>> >> aaa new-model
>> >> !
>> >> !
>> >> aaa authentication login default line
>> >> aaa authentication enable default enable
>> >> aaa authentication ppp default group radius local
>> >> aaa authorization network default group radius
>> >>
>> >> aaa accounting network default start-stop group radius
>> >> aaa session-id common
>> >> ip subnet-zero
>> >> ip cef
>> >> ip domain list mnsi.net
>> >> ip domain name mnsi.net
>> >> ip name-server 206.48.122.2
>> >> ip name-server 206.48.122.8
>> >> !
>> >> ip address-pool local
>> >> ip accounting-threshold 20000
>> >> vpdn enable
>> >> vpdn aaa attribute nas-port vpdn-nas
>> >> vpdn history failure table-size 50
>> >> !
>> >> vpdn-group 1
>> >> ! Default L2TP VPDN group
>> >> accept-dialin
>> >> protocol l2tp
>> >> virtual-template 1
>> >> local name mnsi
>> >> lcp renegotiation always
>> >> l2tp tunnel password 7 0479582A23705F69061601
>> >> !
>>
>> >> vpdn-group 2
>> >> accept-dialin
>> >> protocol pppoe
>> >> virtual-template 1
>> >> pppoe limit per-mac 2
>> >> lcp renegotiation always
>> >> !
>> >> mpls ldp logging neighbor-changes
>> >> !
>> >> !
>> >> !
>> >> bridge irb
>> >> !
>> >> !
>> >> interface ATM0/0/0
>> >> no ip address
>> >> logging event subif-link-status
>> >> load-interval 30
>> >> no atm ilmi-keepalive
>> >> hold-queue 1200 in
>> >> !
>> >> interface Ethernet0/0/1
>> >> ip address dhcp
>> >> shutdown
>> >> !
>> >> interface Ethernet0/0/0
>> >> no ip address
>> >> shutdown
>> >> !
>> >> interface FastEthernet0/0/0
>> >> no ip address
>> >> full-duplex
>> >> !
>> >> interface FastEthernet0/0/0.5
>> >> encapsulation dot1Q 5
>> >> ip address 216.8.137.198 255.255.255.192
>> >> ip ospf priority 0
>> >> !
>> >> interface FastEthernet0/0/0.100
>> >> encapsulation dot1Q 100
>> >> !
>> >> interface Virtual-Template1
>> >> mtu 1454
>> >> ip unnumbered FastEthernet0/0/0.5
>> >> no logging event link-status
>> >> load-interval 30
>> >> peer default ip address pool dynamic1 dynamic2 dynamic3 dynamic4
>> >> ppp authentication pap
>> >> ppp ipcp dns 206.48.122.8 206.48.122.2
>> >> !
>> >> router ospf 1
>> >> log-adjacency-changes
>> >> limit retransmissions dc disable non-dc disable
>> >> summary-address 208.6.78.0 255.255.255.0
>> >> summary-address 206.48.125.0 255.255.255.0
>> >> summary-address 216.8.128.0 255.255.248.0
>> >> redistribute connected subnets
>> >> redistribute static subnets
>> >> network 192.168.10.0 0.0.0.255 area 0
>> >> network 216.8.136.1 0.0.0.0 area 0
>> >> network 216.8.136.5 0.0.0.0 area 0
>> >> network 216.8.136.10 0.0.0.0 area 0
>> >> network 216.8.136.17 0.0.0.0 area 0
>> >> network 216.8.136.21 0.0.0.0 area 0
>> >> network 216.8.136.41 0.0.0.0 area 0
>> >> network 216.8.136.49 0.0.0.0 area 0
>> >> network 216.8.136.61 0.0.0.0 area 0
>> >> network 216.8.136.85 0.0.0.0 area 0
>> >> network 216.8.137.192 0.0.0.63 area 0
>> >> default-information originate always metric 5
>> >> !
>> >> router bgp 7057
>> >> no synchronization
>> >> bgp log-neighbor-changes
>> >> no auto-summary
>> >> !
>> >> ip local pool dynamic1 216.8.128.1 216.8.128.254
>> >> ip local pool dynamic2 216.8.129.1 216.8.129.254
>> >> ip local pool dynamic3 216.8.130.1 216.8.130.254
>> >> ip local pool dynamic4 216.8.131.1 216.8.131.254
>> >> ip classless
>> >> no ip http server
>> >> !
>> >> !
>> >> ip radius source-interface FastEthernet0/0/0.5
>> >> !
>> >> !
>> >> !
>> >> radius-server attribute 32 include-in-access-req
>> >> radius-server host 206.48.122.4 auth-port 1645 acct-port 1646 key
>> norstarsl1
>> >> radius-server key 7 1107161704060A1E17267A
>> >> radius-server authorization permit missing Service-Type
>> >> radius-server vsa send accounting
>> >> !
>> >> line con 0
>> >> line aux 0
>> >> line vty 0 4
>> >> password XXXXXXXXXXXXXX
>> >> !
>> >> ntp clock-period 17181775
>> >> ntp server 206.48.122.98
>> >> end
>> >>
>> >> At 11:22 AM 28/07/2003 -0700, you wrote:
>> >> >That *is* freaky. Could you send me the full output of "show ver" and
>> >> >"show run"? I'd like to recreate this in my lab, but I haven't been
>> >> >able to so far with just these config snippets.
>> >> >
>> >> >Dennis
>> >> >
>> >> >Clayton Zekelman [clayton at mnsi.net] wrote:
>> >> >>
>> >> >>
>> >> >> uacA5-Windsor#sh mem
>> >> >> Head Total(b) Used(b) Free(b) Lowest(b)
>> >> >> Largest(b)
>>
>> >>
>> >> >> Processor 614904A0 74906464 12149748 62756716 62465176
>> >> >> 62445112
>> >> >> I/O 5C00000 37748736 11768424 25980312 25849176
>> >> >> 2584866
>> >> >>
>> >> >> uacA5-Windsor#config t
>> >> >> Enter configuration commands, one per line. End with CNTL/Z.
>> >> >>
>> >> >> uacA5-Windsor(config)#router ospf 1
>> >> >> uacA5-Windsor(config-router)# log-adjacency-changes
>> >> >> uacA5-Windsor(config-router)# limit retransmissions dc disable non-dc
>> >> disable
>> >> >> uacA5-Windsor(config-router)# summary-address 208.6.78.0
255.255.255.0
>> >> >> uacA5-Windsor(config-router)# summary-address 206.48.125.0
255.255.255.0
>> >> >> uacA5-Windsor(config-router)# summary-address 216.8.128.0
255.255.248.0
>> >> >> uacA5-Windsor(config-router)# redistribute connected subnets
>> >> >> uacA5-Windsor(config-router)# redistribute static subnets
>> >> >> uacA5-Windsor(config-router)# network 192.168.10.0 0.0.0.255 area 0
>> >> >> uacA5-Windsor(config-router)# network 216.8.136.1 0.0.0.0 area 0
>> >> >> uacA5-Windsor(config-router)# network 216.8.136.5 0.0.0.0 area 0
>> >> >> uacA5-Windsor(config-router)# network 216.8.136.10 0.0.0.0 area 0
>> >> >> uacA5-Windsor(config-router)# network 216.8.136.17 0.0.0.0 area 0
>> >> >> uacA5-Windsor(config-router)# network 216.8.136.21 0.0.0.0 area 0
>> >> >> uacA5-Windsor(config-router)# network 216.8.136.41 0.0.0.0 area 0
>> >> >> uacA5-Windsor(config-router)# network 216.8.136.49 0.0.0.0 area 0
>> >> >> uacA5-Windsor(config-router)# network 216.8.136.61 0.0.0.0 area 0
>> >> >> uacA5-Windsor(config-router)# network 216.8.136.85 0.0.0.0 area 0
>> >> >> uacA5-Windsor(config-router)# network 216.8.137.192 0.0.0.63 area 0
>> >> >> uacA5-Windsor(config-router)#$originate always metric 5
>> >> >>
>> >> >> uacA5-Windsor(config-router)#exit
>> >> >> uacA5-Windsor(config)#router ospf 2
>> >> >> uacA5-Windsor(config)# log-adjacency-changes
>> >> >> ^
>> >> >> % Invalid input detected at '^' marker.
>> >> >>
>> >> >> uacA5-Windsor(config)# network 216.8.136.100 0.0.0.3 area 1
>> >> >> ^
>> >> >> % Invalid input detected at '^' marker.
>> >> >>
>> >> >> uacA5-Windsor(config)# network 216.8.136.104 0.0.0.3 area 1
>> >> >> ^
>> >> >> % Invalid input detected at '^' marker.
>> >> >>
>> >> >> uacA5-Windsor(config)# network 216.8.136.124 0.0.0.3 area 1
>> >> >> ^
>> >> >> % Invalid input detected at '^' marker.
>> >> >>
>> >> >> uacA5-Windsor(config)# network 216.8.136.128 0.0.0.3 area 1
>> >> >> ^
>> >> >> % Invalid input detected at '^' marker.
>> >> >>
>> >> >> uacA5-Windsor(config)# default-information originate always
>> >> >>
>> >> >> Freaky huh? This is 12.2(15)T5
>> >> >>
>> >> >> At 10:32 AM 28/07/2003 -0700, you wrote:
>> >> >> >You may be out of memory. Can you check the first page of "show mem"
>> >> >> >to see how much you have available?
>> >> >> >
>> >>
>> >> >> >Dennis
>> >> >> >
>> >> >> >Clayton Zekelman [clayton at MNSi.Net] wrote:
>> >> >> >>
>> >> >> >> Just tried to set up a C6400 with an NRP1 with 2 OSPF routing
>> processes,
>> >> >> >> and the command parser wouldn't accept the second task.
>> >> >> >>
>>
>> >> >> >> When I issued the command "router ospf 1", the parser brought me
>> to the
>> >> >> >> (config-router)# prompt, but then, when I issued "router ospf
2", it
>> >> kept
>> >> >> >> me at the (config)# prompt.
>> >> >> >>
>> >> >> >> The same syntax works on a 7200/NPE-300 with 12.2(15)T5
>> >> >> >>
>> >> >> >> I tried this under 12.2(15)T5 and 12.3(1a) on the 6400/NRP1. Any
>> idea
>> >> >> >> whats up?!
>> >> >> >>
>> >> >> >> ---
>> >> >> >> Clayton Zekelman
>> >> >> >> Managed Network Systems Inc. (MNSi)
>> >> >> >> 344-300 Tecumseh Rd. E.
>> >> >> >> Windsor, Ontario
>> >> >> >> N8X 5E8
>> >> >> >>
>> >> >> >> tel. 519-985-8410
>> >> >> >> fax. 519-258-3009
>> >> >> >> _______________________________________________
>> >> >> >> cisco-nsp mailing list cisco-nsp at puck.nether.net
>> >> >> >> http://puck.nether.net/mailman/listinfo/cisco-nsp
>> >> >> >> archive at http://puck.nether.net/pipermail/cisco-nsp/
>> >> >> >_______________________________________________
>> >> >> >cisco-nsp mailing list cisco-nsp at puck.nether.net
>> >> >> >http://puck.nether.net/mailman/listinfo/cisco-nsp
>> >> >> >archive at http://puck.nether.net/pipermail/cisco-nsp/
>> >> >> >
>> >> >>
>> >> >> ---
>> >> >> Clayton Zekelman
>> >> >> Managed Network Systems Inc. (MNSi)
>> >> >> 344-300 Tecumseh Rd. E.
>> >> >> Windsor, Ontario
>> >> >> N8X 5E8
>> >> >>
>> >> >> tel. 519-985-8410
>> >> >> fax. 519-258-3009
>> >> >
>> >>
>> >> ---
>> >> Clayton Zekelman
>> >> Managed Network Systems Inc. (MNSi)
>> >> 344-300 Tecumseh Rd. E.
>> >> Windsor, Ontario
>> >> N8X 5E8
>> >>
>> >> tel. 519-985-8410
>> >> fax. 519-258-3009
>> >
>>
>> ---
>> Clayton Zekelman
>> Managed Network Systems Inc. (MNSi)
>> 344-300 Tecumseh Rd. E.
>> Windsor, Ontario
>> N8X 5E8
>>
>> tel. 519-985-8410
>> fax. 519-258-3009
>
---
Clayton Zekelman
Managed Network Systems Inc. (MNSi)
344-300 Tecumseh Rd. E.
Windsor, Ontario
N8X 5E8
tel. 519-985-8410
fax. 519-258-3009
More information about the cisco-nsp
mailing list