[c-nsp] %Serial1/5 :Header-Compression not configured on interface

[Net Guru]

Hi!,
        I am getting a strange error message in my cisco NPE300. It prepend a line saying "%Serial1/5 :Header-Compression not configured on interface" when ever u give sh run or wr mem command.
Config of the s1/5 is as follows.

Router#sh run int s1/5
Building configuration...

%Serial1/5 :Header-Compression not configured on interface
Current configuration : 265 bytes
!
interface Serial1/5
 description Link to ABC
 bandwidth 64
 no ip address
 no ip proxy-arp
 encapsulation frame-relay
 ip route-cache flow
 no ip mroute-cache
 serial restart-delay 0
 no fair-queue
 frame-relay lmi-type ansi
 frame-relay intf-type dce
end

Router#sh int s1/5
Serial1/5 is down, line protocol is down
  Hardware is M8T-V.35
  Description: Link to ABC
  MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation FRAME-RELAY, crc 16, loopback not set
  Keepalive set (10 sec)
  Restart-Delay is 0 secs
  LMI enq sent  0, LMI stat recvd 0, LMI upd recvd 0
  LMI enq recvd 0, LMI stat sent  0, LMI upd sent  0, DCE LMI down
  LMI DLCI 0  LMI type is ANSI Annex D  frame relay DCE
  FR SVC disabled, LAPF state down
  Broadcast queue 0/64, broadcasts sent/dropped 0/0, interface broadcasts 0
  Last input never, output never, output hang never
  Last clearing of "show interface" counters 1w0d
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     0 packets output, 0 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 output buffer failures, 0 output buffers swapped out
     0 carrier transitions     DCD=down  DSR=down  DTR=up  RTS=up  CTS=down

Router#
Router#sh ver
Cisco Internetwork Operating System Software
IOS (tm) 7200 Software (C7200-JS-M), Version 12.3(2)T8, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Fri 03-Sep-04 04:52 by eaarmas
Image text-base: 0x60008954, data-base: 0x620FE000

ROM: System Bootstrap, Version 12.0(19990210:195103) [12.0XE 105], DEVELOPMENT SOFTWARE
BOOTLDR: 7200 Software (C7200-KBOOT-M), Version 12.1(8a)E, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

Router uptime is 17 weeks, 5 days, 14 hours, 25 minutes
System returned to ROM by power-on
System restarted at 02:43:14 IST Sun Apr 17 2005
System image file is "disk0:c7200-js-mz.123-2.T8.bin"

cisco 7206VXR (NPE300) processor (revision D) with 122880K/40960K bytes of memory.
Processor board ID 20394670
R7000 CPU at 262Mhz, Implementation 39, Rev 2.1, 256KB L2, 2048KB L3 Cache
6 slot VXR midplane, Version 2.0

Last reset from power-on
Channelized E1, Version 1.0.
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
Primary Rate ISDN software, Version 1.1.

PCI bus mb0_mb1 has 400 bandwidth points
PCI bus mb2 has 0 bandwidth points

1 Ethernet/IEEE 802.3 interface(s)
1 Gigabit Ethernet/IEEE 802.3 interface(s)
53 Serial network interface(s)
2 Channelized E1/PRI port(s)
125K bytes of non-volatile configuration memory.

62976K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes).
8192K bytes of Flash internal SIMM (Sector size 256K).
Configuration register is 0x2102

Router#

Thanks & Regards,
 
NG