[c-nsp] Cisco 7200VXR/NPE-300 & NPE-G1 Crash with PA-2FE-FX

[Craig Spiers]

Hi all

Has anyone come across a 7200/vxr with npe-300 (also npe-g1) crashing when
an PA-2FE-FX (10/100 version) is installed?

Only seems to happen when both ports are connected.. IOS version Is 12.2.29
- but also crashes on 12.3


Crash dump:
Jul 17 12:00:28.764 +1200: %LINEPROTO-5-UPDOWN: Line protocol on Interface
FastEthernet2/1, changed state to up
%ERR-1-SERR: PCI bus system/parity error
%ERR-1-FATAL: Fatal error interrupt, No reloading
 err_stat=0x80, err_enable=0xFF, mgmt_event=0x40

System bridge dump:

Bridge 0, for PA Bay 0 (I/O Card, PCMCIA, Interfaces), Handle=0
DEC21150 bridge chip, config=0x0
(0x00):dev, vendor id       = 0x00231011
(0x04):status, command      = 0x02B00147
(0x08):class code, revid    = 0x06040006
(0x0C):hdr, lat timer, cls  = 0x00012E10
(0x18):sec lat,cls & bus no = 0x18020100
(0x1C):sec status, io base  = 0x02A03101
(0x20):mem base & limit     = 0x48704000
(0x24):prefetch membase/lim = 0x0001FF01
(0x30):io base/lim upper16  = 0x00000000
(0x3C):bridge ctrl          = 0x00030000
(0x40):arb/serr, chip ctrl  = 0x02000000
(0x64):serr disable, gpio   = 0xF0000000
(0x68):sec clk ctrl,serrsta = 0x000001FF

Bridge 1, for PA bay 1, 3 and 5, Handle=1
DEC21150 bridge chip, config=0x0
(0x00):dev, vendor id       = 0x00231011
(0x04):status, command      = 0x02B00147
(0x08):class code, revid    = 0x06040006
(0x0C):hdr, lat timer, cls  = 0x00012E10
(0x18):sec lat,cls & bus no = 0x18090400
(0x1C):sec status, io base  = 0x02A09141
(0x20):mem base & limit     = 0x4AF04880
(0x24):prefetch membase/lim = 0x0001FF01
(0x30):io base/lim upper16  = 0x00000000
(0x3C):bridge ctrl          = 0x00030000
(0x40):arb/serr, chip ctrl  = 0x02000000
(0x64):serr disable, gpio   = 0xF0000000
(0x68):sec clk ctrl,serrsta = 0x000001FF

Bridge 2, for PA bay 2, 4 and 6, Handle=2
DEC21150 bridge chip, config=0x0
(0x00):dev, vendor id       = 0x00231011
(0x04):status, command      = 0x42B00147
         Signaled System Error  on primary bus
(0x08):class code, revid    = 0x06040006
(0x0C):hdr, lat timer, cls  = 0x00012E10
(0x18):sec lat,cls & bus no = 0x180F0A00
(0x1C):sec status, io base  = 0x42A0F1A1
         Signaled System Error  on secondary bus
(0x20):mem base & limit     = 0x4FF04D00
(0x24):prefetch membase/lim = 0x0001FF01
(0x30):io base/lim upper16  = 0x00200020
(0x3C):bridge ctrl          = 0x00030000
(0x40):arb/serr, chip ctrl  = 0x02000000
(0x64):serr disable, gpio   = 0xF0000000
(0x68):sec clk ctrl,serrsta = 0x000001FF

PA bridge dump:

Bridge 5, Port Adaptor 2, Handle=2
DEC21150 bridge chip, config=0x0
(0x00):dev, vendor id       = 0x00231011
(0x04):status, command      = 0x42B00147
         Signaled System Error  on primary bus
(0x08):class code, revid    = 0x06040006
(0x0C):hdr, lat timer, cls  = 0x00011A10
(0x18):sec lat,cls & bus no = 0x180B0B0A
(0x1C):sec status, io base  = 0x82A0B1A1
         Detected Parity Error  on secondary bus
(0x20):mem base & limit     = 0x4D704D00
(0x24):prefetch membase/lim = 0x0001FF01
(0x30):io base/lim upper16  = 0x00200020
(0x3C):bridge ctrl          = 0x07030000
(0x40):arb/serr, chip ctrl  = 0x02000000
(0x64):serr disable, gpio   = 0xF0000000
(0x68):sec clk ctrl,serrsta = 0x000101FF


=== Flushing messages (12:00:54 +1200 Sun Jul 17 2005) ===