[c-nsp] Help configuring a Cisco 1841 with wic 1DSU-T1-v2

[Church, Chuck]

Doesn't RFC 1483 always refer to ATM?  This sounds like an ATM circuit.
That'll never work with a non-ATM interface. 


Chuck Church
Lead Design Engineer
CCIE #8776, MCNE, MCSE
Netco Government Services - Design & Implementation Team
1210 N. Parker Rd.
Greenville, SC 29609
Home office: 864-335-9473
Cell: 703-819-3495
cchurch at netcogov.com
PGP key: http://pgp.mit.edu:11371/pks/lookup?op=get&search=0x4371A48D 


-----Original Message-----
From: cisco-nsp-bounces at puck.nether.net
[mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of William L.
Thomson Jr.
Sent: Friday, May 13, 2005 7:46 PM
To: cisco-nsp at puck.nether.net
Subject: [c-nsp] Help configuring a Cisco 1841 with wic 1DSU-T1-v2

I have been pulling my hair out for hours trying to configure the darn
T1 interface. It's a T1 provided by FDN and is a bridged T1. FDN
provided a Netopia which I am trying to replace with the Cisco.

This is the netopia's config that I am trying to migrate.

         Operation Mode...                  CM-HDLC
         Line Encoding...                   B8ZS
         Framing Mode...                    ESF
         Transmit ANSI PRMs:                No
         AutoDetect DS0 Channels:           No
         Number of DS0 Channels:            24
 
 
         Buildout (-dB)...                  0-0.6
         Channel Data Rate...               Nx64k
         Clock Source...                    Network
         Data Link Encapsulation...         RFC1483
         RFC1483 Mode...                    Bridged 1483
         PPP over Ethernet (PPPoE):         Off 


These are the errors I am getting


*May 13 22:23:04.099: Illegal HDLC serial type code 43690, PC=0x61134FD4
*May 13 22:23:04.951: Serial0/0/0: HDLC myseq 245, mineseen 0, yourseen
0, line down
*May 13 22:23:05.099: Illegal HDLC serial type code 43690, PC=0x61134FD4
*May 13 22:23:05.099: Illegal HDLC serial type code 43690, PC=0x61134FD4
*May 13 22:23:05.867: Serial0/0/0: attempting to restart
*May 13 22:23:05.867:  gt96k_mbrd_serial_mode_reg_init:: was DTE, now
set to DTE
*May 13 22:23:05.867:  DTE idb->dte_interface = DTE
*May 13 22:23:05.867: Dscc4(0/0): DCD is up.
*May 13 22:23:06.099: Illegal HDLC serial type code 43690, PC=0x61134FD4
*May 13 22:23:06.099: Illegal HDLC serial type code 43690, PC=0x61134FD4
 


Now the hdlc ones went away per someones suggestion to use ppp
encapsulation instead of HDLC.

I am not sure if I need to setup a bridge virtual interface or not.


-- 
Sincerely,
William L. Thomson Jr.
Support Group
Obsidian-Studios, Inc.
http://www.obsidian-studios.com

_______________________________________________
cisco-nsp mailing list  cisco-nsp at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/