[c-nsp] PPPoE Session Limit?

[Graham Wooden]

Here is the config - I took out some of the irrelevant stuff, but enough to
get a bug picture.


service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
aaa new-model
!
!
aaa authentication login radius local
aaa authentication login local local
aaa authentication ppp default local
aaa authorization network default local
aaa accounting network default start-stop group radius
aaa session-id common
ip subnet-zero
ip cef
!
!
virtual-profile virtual-template 10
vpdn enable
vpdn session-limit 800
!         
vpdn-group bas01
 accept-dialin
  protocol any
  virtual-template 10
 session-limit 800
 terminate-from hostname atlngacs70w
 local name BBG-Gateway
 lcp renegotiation on-mismatch
 l2tp tunnel password 7 xxxxxxxxxxxxxxxxx
 l2tp tunnel timeout no-session never
!
username user1 at domain.local privilege 0 password 7 xxxxxxxxxxxxxxxxx
username user2 at domain.local privilege 0 password 7 xxxxxxxxxxxxxxxxx
username user3 at domain.local privilege 0 password 7 xxxxxxxxxxxxxxxxx
username user4 at domain.local privilege 0 password 7 xxxxxxxxxxxxxxxxx
username user5 at domain.local privilege 0 password 7 xxxxxxxxxxxxxxxxx
username user6 at domain.local privilege 0 password 7 xxxxxxxxxxxxxxxxx
username user7 at domain.local privilege 0 password 7 xxxxxxxxxxxxxxxxx
!
interface Loopback1
 no ip address
!
interface Vif1
 no ip address
!
interface FastEthernet0/0
 ip address xx.xxx.xxx.xx 255.255.255.224
 duplex auto
 speed 100
!
interface ATM1/0
 no ip address
 no ip route-cache cef
 no ip route-cache
 shutdown
 no atm ilmi-keepalive
 no scrambling-payload
!
interface ATM1/1
 no ip address
 no ip route-cache cef
 no ip route-cache
 no atm ilmi-keepalive
 scrambling-payload
 arp snap
 arp timeout 0
!
interface ATM1/1.3 point-to-point
 description Bellsouth BBG Connection
 mtu 9180
 ip address 10.x.x.x 255.255.255.252
 no ip route-cache
 no ip mroute-cache
 pvc 1/37 
  encapsulation aal5snap
!
!
interface ATM1/2
 no ip address
 shutdown
 no atm ilmi-keepalive
 no scrambling-payload
!
interface ATM1/3
 no ip address
 no ip route-cache cef
 no ip route-cache
 no ip mroute-cache
 shutdown
 no atm ilmi-keepalive
 no scrambling-payload
!
interface Virtual-Template10
 description Bellsouth BBG Connection
 mtu 9180
 ip address xx.xxx.xxx.193 255.255.255.192
 ip access-group 105 out
 ip mroute-cache
 peer default ip address pool ppp
 keepalive 200
 ppp authentication chap pap
 ppp ipcp dns xx.xxx.xxx.xxx
 ppp ipcp mask 255.255.255.192
!
router ospf xxx
 log-adjacency-changes
 redistribute static subnets
 network xx.xxx.xxx.xx  0.0.0.63 area 0
!
ip local pool ppp xx.xxx.xxx.200 xx.xxx.xxx.253
no ip http server
ip classless
!



On 4/10/06 12:12 PM, "Joe Maimon" <jmaimon at ttec.com> wrote:

> 
> 
> Graham Wooden wrote:
> 
>> Hi all,
>> 
> 
>> get in. Or if someone drops off, a user that couldn't get in, will now.
>> 
> 
> It authenticates but doesnt get any IP assigned to it. Can you post your
> config? Can you check if your IP pool is full?
> 
>