[c-nsp] Help with configuration

[Victor Cappuccio]

Hello,

 

Can any one please tell me, how to configure the following QOS MQC in a
7600?

Any resource to read, I've configured this on one of this equipment:

 

IP7COL01(config-pmap-c)# class-map Grupo-Interno-QOS:5

IP7COL01(config-cmap)# match ip prec 5

IP7COL01(config-cmap)# class-map Grupo-Interno-QOS:4

IP7COL01(config-cmap)# match ip prec 4

IP7COL01(config-cmap)# class-map Grupo-Interno-QOS:1

IP7COL01(config-cmap)# match ip pre  1

IP7COL01(config-cmap)# policy-map ip-A-mpls-Egreso

IP7COL01(config-pmap)# class Grupo-Interno-QOS:5

IP7COL01(config-pmap-c)#set mpls experimental topmost 5

IP7COL01(config-pmap-c)#priority percent 50

IP7COL01(config-pmap-c)#class Grupo-Interno-QOS:4

IP7COL01(config-pmap-c)#set mpls experimental topmost 4

IP7COL01(config-pmap-c)#bandwidth percent 20

IP7COL01(config-pmap-c)#class Grupo-Interno-QOS:1

IP7COL01(config-pmap-c)#set mpls experimental topmost 1

IP7COL01(config-pmap-c)#bandwidth percent 20

IP7COL01(config-pmap-c)#random-detect 

IP7COL01(config-pmap-c)#class class-default

IP7COL01(config-pmap-c)#set mpls experimental topmost 0

IP7COL01(config-pmap-c)#random-detect 

IP7COL01(config-pmap-c)#fair 

IP7COL01(config-pmap-c)#

IP7COL01(config-pmap-c)#

IP7COL01(config-pmap-c)#int g9/24

IP7COL01(config-if)#ser out ip-A-mpls-Egreso

priority command is not supported in output direction for this interface

Configuration failed!

 

Now neither band percent

 

IP7COL01(config-if)#policy-map ip-A-mpls-Egreso

IP7COL01(config-pmap)#class Grupo-Interno-QOS:5

IP7COL01(config-pmap-c)#no priority percent 50

IP7COL01(config-pmap-c)#bandwidth percent 20

IP7COL01(config-pmap-c)#int g9/24

IP7COL01(config-if)#ser out ip-A-mpls-Egreso           

bandwidth percent command is not supported for this interface

Configuration failed!

IP7COL01(config-if)#

 

Then I see that the 7600 uses 

 

IP7COL01(config-if)#wrr-queue ?

  bandwidth      Configure WRR minimum bandwidth with weights or
percentages

  cos-map        Configure cos-map for a queue threshold

  queue-limit    Configure queue-limit

  random-detect  Configure random-detect

  threshold      Configure queue tail-drop thresholds

 

 

 

IP7COL01#conf ter

Enter configuration commands, one per line.  End with CNTL/Z.

IP7COL01(config)#mls qos 

IP7COL01(config)#^Z

IP7COL01#show mls qos module 9

  QoS is enabled globally

  Policy marking depends on port_trust

  QoS ip packet dscp rewrite enabled globally

  Input mode for GRE Tunnel is Pipe mode

  Input mode for MPLS is Pipe mode

  Vlan or Portchannel(Multi-Earl) policies supported: Yes

  Egress policies supported: Yes

 

  QoS global counters:

    Total packets: 42717643

    IP shortcut packets: 0

    Packets dropped by policing: 0

    IP packets with TOS changed by policing: 119

    IP packets with COS changed by policing: 84

    Non-IP packets with COS changed by policing: 33

    MPLS packets with EXP changed by policing: 0

          

IP7COL01#show mls qos ip g9/24

   [In] Default.   [Out] Default.

 QoS Summary [IPv4]:      (* - shared aggregates, Mod - switch module)

 

      Int Mod Dir  Class-map DSCP  Agg  Trust Fl   AgForward-By
AgPoliced-By

                                   Id         Id


------------------------------------------------------------------------
-------

    Gi9/24  5  In    Default    0    0*    No  0         840776
0

IP7COL01#

 

 

Is there a way to provide that MQC configuration but for that 7600
switch ??

Traffic is coming IP and going out MPLS, also I need to do PHB
classification on that switch 

 

 

 IP7COL01#show ver | b cisco CISCO7609

cisco CISCO7609 (R7000) processor (revision 1.2) with 458720K/65536K
bytes of memory.

Processor board ID FOX103400QE

SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache

Last reset from s/w reset

1 SIP-200 controller (2 ATM)(2 POS)(1 Channelized OC3/STM-1).

17 Virtual Ethernet interfaces

76 Gigabit Ethernet interfaces

4 Ten Gigabit Ethernet interfaces

2 ATM interfaces

2 Packet over SONET interfaces

1 Channelized STM-1 port

1917K bytes of non-volatile configuration memory.

8192K bytes of packet buffer memory.

 

65536K bytes of Flash internal SIMM (Sector size 512K).

Configuration register is 0x2102

 

IP7COL01#show mod 9

Mod Ports Card Type                              Model
Serial No.

--- ----- -------------------------------------- ------------------
-----------

  9   24  CEF720 24 port 1000mb SFP              WS-X6724-SFP
XXXXX

 

Mod MAC addresses                       Hw    Fw           Sw
Status

--- ---------------------------------- ------ ------------ ------------
-------

  9  0018.b9c4.8298 to 0018.b9c4.82af   2.4   12.2(14r)S5  12.2(33)SRA1
Ok

 

Mod  Sub-Module                  Model              Serial       Hw
Status 

---- --------------------------- ------------------ ----------- -------
-------

  9  Centralized Forwarding Card WS-F6700-CFC       XXXXX   2.0    Ok

 

Mod  Online Diag Status 

---- -------------------

9        Pass

 

 

Thanks and sorry for bad english

 

Victor.-