[c-nsp] ADSL on 2621 or 2621XM

Mathias at TelecityRedbus.com Mathias at TelecityRedbus.com
Wed Oct 4 11:55:46 EDT 2006


Adrian,

I guess I'll need to upgrade my code (the current one is 12.1.20 IP
PLUS). Where do you then specify the PVC? 

Mathias,

-----Original Message-----
From: Adrian Chadd [mailto:adrian at creative.net.au] 
Sent: 04 October 2006 16:29
To: Mathias Kenfack-Tabakem (LON)
Cc: cisco-nsp at puck.nether.net
Subject: Re: [c-nsp] ADSL on 2621 or 2621XM

I'm using the pppoe-client support. Amusingly, it needs pppoe-client
over
Ethernet support - there's pppoe over ATM but thats not what you want.

(The modem is talking ATM for you and giving you pppoe frames.)

Something like:

vpdn-enable
!
int fa0/0
 description XC to ADSL modem
 pppoe enable group global
 pppoe-client dial-pool-number 1
!
int dialer1
 description ADSL virtual session
 ip address negotiated
 no ip redirects
 no ip unreachables
 dialer-group 1
 dialer pool 1
 <insert your relevant PPP stuff here>
!
dialer-list 1 protocol ip permit
!
ip route 0.0.0.0 0.0.0.0 dialer1
!

then show vpdn sess:

PPPoE Session Information Total tunnels 1 sessions 1

PPPoE Session Information
Uniq ID  PPPoE  RemMAC          Port                    VT  VA
State
           SID  LocMAC                                      VA-st
    N/A   2242  0090.1aa0.6fc8  Fa0/0                  Di1  Vi3
UP      
                0003.e38d.b6c0                              UP         

Search the Cisco site for PPPoE ADSL ethernet or something. There's an
example configuration
or two for PPPoE using an ethernet interface rather than ATM lurking
about.

HTH,


Adrian


On Wed, Oct 04, 2006, Mathias at TelecityRedbus.com wrote:
> Hi Guys,
> 
> This is for my home ADSL.
> I have a 2621 fa0/0 connected to Linksys ADSL2MUE ADSL2 Modem Ethernet
> port. Linksys is setup in bridge mode (forward all login detail and
> public IP to attached router). Not sure if I need something else (the
> 2621 has only the 2 default Fast Ethernet ports.
> I can't get interface atm0 on the router. I believe this is where I
> configure the PVC or is there any other place on the router to do
that?
> 
> Not sure if you need this but my ADSL speed is: 8M download / 512K
> upload
> 
> Regards,
> Mathias
> This e-mail is intended only for the use of the addressees named above
and may be confidential. 
> If you are not an addressee you must not use any information contained
in nor copy it nor inform any person other than the addressees of its
existence or contents. 
> 
> 
> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/
This e-mail is intended only for the use of the addressees named above and may be confidential. 
If you are not an addressee you must not use any information contained in nor copy it nor inform any person other than the addressees of its existence or contents. 




More information about the cisco-nsp mailing list