[c-nsp] 7206 error
David Coulson
david at davidcoulson.net
Fri Sep 8 17:18:27 EDT 2006
One of my 7206 routers rebooted out of the blue and now does this. Looks
like the backplane is shot, but I don't know if it's the NPE that might
be causing an issue, or if it's something else. It's a 7206VXR with
NPE-300. All it has in it is IO-FE-TX and a couple of PA-MC-8T1 cards.
Short of throwing it out, anyone got suggestions as to what might be
causing this? It used to be running 12.3(10), and was running happily
for about a year in it's current config.
%ERR-1-GT64120 (PCI-1): Fatal error, Parity error on master read
GT=0xB4000000, cause=0x00100000, mask=0x00D01D00, real_cause=0x00100000
--------------------------------------------------------------------
Possible hardware fault. This could be an one time occurence,
upon reccurence please collect crashinfo, "show tech"
and contact Cisco Technical Support.
----------------------------------------------------------------------
bus_err_high=0x00000000, bus_err_low=0x00000000, addr_decode_err=0x00000470
%ERR-1-FATAL: Fatal error interrupt, No reloading
err_stat=0x1, err_enable=0xFF, mgmt_event=0x40
GT64120-0 External PCI Configuration registers:
PCI_0:
Vendor / Device ID : 0xAB112046 (b/s 0x462011AB)
Status / Command : 0x4601A002 (b/s 0x02A00146)
Class / Revision : 0x03008005 (b/s 0x05800003)
Latency : 0x0F000000 (b/s 0x0000000F)
RAS[1:0] Base : 0x00000020 (b/s 0x20000000)
RAS[3:2] Base : 0x00000022 (b/s 0x22000000)
CS[2:0] Base : 0x00000000 (b/s 0x00000000)
CS[3] Base : 0x00000000 (b/s 0x00000000)
Mem Map Base : 0x00000014 (b/s 0x14000000)
IO Map Base : 0x00000000 (b/s 0x00000000)
Subsystem Vendor / D : 0x00000000 (b/s 0x00000000)
Int Pin / Line : 0x00010000 (b/s 0x00000100)
Swap RAS[1:0] Base : 0x000000E0 (b/s 0xE0000000)
Swap RAS[3:2] Base : 0x000000E2 (b/s 0xE2000000)
Swap CS[3] Base : 0x00000000 (b/s 0x00000000)
PCI_1:
Vendor / Device ID : 0xAB112046 (b/s 0x462011AB)
Status / Command : 0x4601A083 (b/s 0x83A00146)
Class / Revision : 0x03008005 (b/s 0x05800003)
Latency : 0x0F000000 (b/s 0x0000000F)
RAS[1:0] Base : 0x00000020 (b/s 0x20000000)
RAS[3:2] Base : 0x00000022 (b/s 0x22000000)
CS[2:0] Base : 0x00000000 (b/s 0x00000000)
CS[3] Base : 0x00000000 (b/s 0x00000000)
Mem Map Base : 0x00000014 (b/s 0x14000000)
IO Map Base : 0x00000000 (b/s 0x00000000)
Subsystem Vendor / D : 0x00000000 (b/s 0x00000000)
Int Pin / Line : 0x00010000 (b/s 0x00000100)
Swap RAS[1:0] Base : 0x000000E0 (b/s 0xE0000000)
Swap RAS[3:2] Base : 0x000000E2 (b/s 0xE2000000)
Swap CS[3] Base : 0x00000000 (b/s 0x00000000)
GT64120-1 External PCI Configuration registers:
PCI_0:
Vendor / Device ID : 0xAB112046 (b/s 0x462011AB)
Status / Command : 0x4601A002 (b/s 0x02A00146)
Class / Revision : 0x03008005 (b/s 0x05800003)
Latency : 0x0F000000 (b/s 0x0000000F)
RAS[1:0] Base : 0x00000000 (b/s 0x00000000)
RAS[3:2] Base : 0x00000008 (b/s 0x08000000)
CS[2:0] Base : 0x00000000 (b/s 0x00000000)
CS[3] Base : 0x00000000 (b/s 0x00000000)
Mem Map Base : 0x00000015 (b/s 0x15000000)
IO Map Base : 0x00000000 (b/s 0x00000000)
Subsystem Vendor / D : 0x00000000 (b/s 0x00000000)
Int Pin / Line : 0x00010000 (b/s 0x00000100)
Swap RAS[1:0] Base : 0x000000C0 (b/s 0xC0000000)
Swap RAS[3:2] Base : 0x000000C8 (b/s 0xC8000000)
Swap CS[3] Base : 0x00000000 (b/s 0x00000000)
PCI_1:
Vendor / Device ID : 0xAB112046 (b/s 0x462011AB)
Status / Command : 0x4601A002 (b/s 0x02A00146)
Class / Revision : 0x03008005 (b/s 0x05800003)
Latency : 0x0F000000 (b/s 0x0000000F)
RAS[1:0] Base : 0x00000000 (b/s 0x00000000)
RAS[3:2] Base : 0x00000008 (b/s 0x08000000)
CS[2:0] Base : 0x00000000 (b/s 0x00000000)
CS[3] Base : 0x00000000 (b/s 0x00000000)
Mem Map Base : 0x00000015 (b/s 0x15000000)
IO Map Base : 0x00000000 (b/s 0x00000000)
Subsystem Vendor / D : 0x00000000 (b/s 0x00000000)
Int Pin / Line : 0x00010000 (b/s 0x00000100)
Swap RAS[1:0] Base : 0x000000C0 (b/s 0xC0000000)
Swap RAS[3:2] Base : 0x000000C8 (b/s 0xC8000000)
Swap CS[3] Base : 0x00000000 (b/s 0x00000000)
System bridge dump:
Bridge 0, for PA Bay 0 (I/O Card, PCMCIA, Interfaces), Handle=0
DEC21150 bridge chip, Primary Bus 0, Secondary Bus 1,config=0x0
(0x00):dev, vendor id = 0x00231011
(0x04):status, command = 0x02B00147
(0x08):class code, revid = 0x06040006
(0x0C):hdr, lat timer, cls = 0x00012E10
(0x18):sec lat,cls & bus no = 0x18020100
(0x1C):sec status, io base = 0x02A03101
(0x20):mem base & limit = 0x48704000
(0x24):prefetch membase/lim = 0x0001FF01
(0x30):io base/lim upper16 = 0x00000000
(0x3C):bridge ctrl = 0x00030000
(0x40):arb/serr, chip ctrl = 0x02000000
(0x64):serr disable, gpio = 0xF0000000
(0x68):sec clk ctrl,serrsta = 0x000001FF
Bridge 1, for PA bay 1, 3 and 5, Handle=1
DEC21150 bridge chip, Primary Bus 0, Secondary Bus 4,config=0x0
(0x00):dev, vendor id = 0x00231011
(0x04):status, command = 0x02B00147
(0x08):class code, revid = 0x06040006
(0x0C):hdr, lat timer, cls = 0x00012E10
(0x18):sec lat,cls & bus no = 0x18090400
(0x1C):sec status, io base = 0x02A09141
(0x20):mem base & limit = 0x4AF04880
(0x24):prefetch membase/lim = 0x0001FF01
(0x30):io base/lim upper16 = 0x00000000
(0x3C):bridge ctrl = 0x00030000
(0x40):arb/serr, chip ctrl = 0x02000000
(0x64):serr disable, gpio = 0xF0000000
(0x68):sec clk ctrl,serrsta = 0x000001FF
Bridge 2, for PA bay 2, 4 and 6, Handle=2
DEC21150 bridge chip, Primary Bus 0, Secondary Bus 10,config=0x0
(0x00):dev, vendor id = 0x00231011
(0x04):status, command = 0x02B00147
(0x08):class code, revid = 0x06040006
(0x0C):hdr, lat timer, cls = 0x00012E10
(0x18):sec lat,cls & bus no = 0x180F0A00
(0x1C):sec status, io base = 0x83A0F1A1
Detected Parity Error on secondary bus
Data Parity Detected on secondary bus
(0x20):mem base & limit = 0x4FF04D00
(0x24):prefetch membase/lim = 0x0001FF01
(0x30):io base/lim upper16 = 0x00200020
(0x3C):bridge ctrl = 0x00030000
(0x40):arb/serr, chip ctrl = 0x02000000
(0x64):serr disable, gpio = 0xF0000000
(0x68):sec clk ctrl,serrsta = 0x000001FF
PA bridge dump:
Bridge 5, Port Adaptor 2, Handle=2
DEC21150 bridge chip, Primary Bus 10, Secondary Bus 11,config=0x0
(0x00):dev, vendor id = 0x00231011
(0x04):status, command = 0x02B00147
(0x08):class code, revid = 0x06040006
(0x0C):hdr, lat timer, cls = 0x00011A10
(0x18):sec lat,cls & bus no = 0x180B0B0A
(0x1C):sec status, io base = 0x22A0B1A1
Received Master Abort on secondary bus
(0x20):mem base & limit = 0x4D704D00
(0x24):prefetch membase/lim = 0x0001FF01
(0x30):io base/lim upper16 = 0x00200020
(0x3C):bridge ctrl = 0x03030000
(0x40):arb/serr, chip ctrl = 0x02000000
(0x64):serr disable, gpio = 0xF0000000
(0x68):sec clk ctrl,serrsta = 0x000001FF
Bridge 7, Port Adaptor 4, Handle=4
DEC21150 bridge chip, Primary Bus 10, Secondary Bus 12,config=0x0
(0x00):dev, vendor id = 0x00231011
(0x04):status, command = 0x02B00147
(0x08):class code, revid = 0x06040006
(0x0C):hdr, lat timer, cls = 0x00011A10
(0x18):sec lat,cls & bus no = 0x180C0C0A
(0x1C):sec status, io base = 0xA3A0D1C1
Detected Parity Error on secondary bus
Received Master Abort on secondary bus
Data Parity Detected on secondary bus
(0x20):mem base & limit = 0x4DF04D80
(0x24):prefetch membase/lim = 0x0001FF01
(0x30):io base/lim upper16 = 0x00200020
(0x3C):bridge ctrl = 0x03030000
(0x40):arb/serr, chip ctrl = 0x02000000
(0x64):serr disable, gpio = 0xF0000000
(0x68):sec clk ctrl,serrsta = 0x000001FF
Bridge 8, Port Adaptor 5, Handle=5
DEC21150 bridge chip, Primary Bus 4, Secondary Bus 7,config=0x0
(0x00):dev, vendor id = 0x00231011
(0x04):status, command = 0x02B00147
(0x08):class code, revid = 0x06040006
(0x0C):hdr, lat timer, cls = 0x00011A10
(0x18):sec lat,cls & bus no = 0x18070704
(0x1C):sec status, io base = 0x02A09181
(0x20):mem base & limit = 0x49F04980
(0x24):prefetch membase/lim = 0x0001FF01
(0x30):io base/lim upper16 = 0x00000000
(0x3C):bridge ctrl = 0x03030000
(0x40):arb/serr, chip ctrl = 0x02000000
(0x64):serr disable, gpio = 0xF0000000
(0x68):sec clk ctrl,serrsta = 0x000001FF
Bridge 9, Port Adaptor 6, Handle=6
DEC21150 bridge chip, Primary Bus 10, Secondary Bus 13,config=0x0
(0x00):dev, vendor id = 0x00231011
(0x04):status, command = 0x02B00147
(0x08):class code, revid = 0x06040006
(0x0C):hdr, lat timer, cls = 0x00011A10
(0x18):sec lat,cls & bus no = 0x180D0D0A
(0x1C):sec status, io base = 0x02A0F1E1
(0x20):mem base & limit = 0x4E704E00
(0x24):prefetch membase/lim = 0x0001FF01
(0x30):io base/lim upper16 = 0x00200020
(0x3C):bridge ctrl = 0x03030000
(0x40):arb/serr, chip ctrl = 0x02000000
(0x64):serr disable, gpio = 0xF0000000
(0x68):sec clk ctrl,serrsta = 0x000001FF
=== Flushing messages (21:32:17 UTC Fri Sep 8 2006) ===
Buffered messages:
Queued messages:
21:32:17 UTC Fri Sep 8 2006: Interrupt exception, CPU signal 22, PC = 0x0
--------------------------------------------------------------------
Possible software fault. Upon reccurence, please collect
crashinfo, "show tech" and contact Cisco Technical Support.
--------------------------------------------------------------------
-Traceback= 0 0
$0 : 00000000, AT : 00000000, v0 : 00000000, v1 : 00000000
a0 : 00000000, a1 : 00000000, a2 : 00000000, a3 : 00000000
t0 : 00000000, t1 : 00000000, t2 : 00000000, t3 : 00000000
t4 : 00000000, t5 : 00000000, t6 : 00000000, t7 : 00000000
s0 : 00000000, s1 : 00000000, s2 : 00000000, s3 : 00000000
s4 : 00000000, s5 : 00000000, s6 : 00000000, s7 : 00000000
t8 : 00000000, t9 : 00000000, k0 : 00000000, k1 : 00000000
gp : 00000000, sp : 00000000, s8 : 00000000, ra : 00000000
EPC : 00000000, ErrorEPC : 00000000, SREG : 00000000
MDLO : 00000000, MDHI : 00000000, BadVaddr : 00000000
Cause 00000000 (Code 0x0): Interrupt exception
File bootflash:crashinfo_20060908-213217 Device Error :No such device
*** System received an Error Interrupt ***
signal= 0x16, code= 0x0, context= 0x639d47b8
PC = 0x6080f118, Cause = 0x2020, Status Reg = 0x34008002
David
More information about the cisco-nsp
mailing list