[c-nsp] Cisco WIC-1DSU-T1-V2 + 2811 + 12.4(11)T ??

[joe mcguckin]

I can't get this combination to bring up a T1.

Configured as
     encaps hdlc
     service-module t1 clock source line
     service-module t1 line b8zs
     service-module t1 frame esf
     service-module t1 timeslots all

Indicator LED on WIC is green, with no alarms.



Turning on debugging shows no keepalives seen:

yourname#debug serial event
Serial interface event debugging is on
yourname#debug serial interface
Serial network interface debugging is on
yourname#debug serial packet
Serial network packets debugging is on
yourname#
*Jan 23 22:30:23.227:  DTE idb->dte_interface = DTE
*Jan 23 22:30:23.227: Dscc4(Serial0/0/0): DCD is up.

*Jan 23 22:30:25.227: %LINK-3-UPDOWN: Interface Serial0/0/0, changed  
state to up
*Jan 23 22:30:26.227: %LINEPROTO-5-UPDOWN: Line protocol on Interface  
Serial0/0/0, changed state to up
*Jan 23 22:30:30.391: Serial0/0/0: HDLC myseq 0, mineseen 0, yourseen  
0, line up
*Jan 23 22:30:40.391: Serial0/0/0: HDLC myseq 1, mineseen 0, yourseen  
0, line up
*Jan 23 22:30:50.391:  gt96k_mbrd_serial_mode_reg_init:: was DTE, now  
set to DTE
*Jan 23 22:30:50.391:  DTE idb->dte_interface = DTE
*Jan 23 22:30:50.391: Dscc4(Serial0/0/0): DCD is up.

*Jan 23 22:30:50.391: Serial0/0/0: HDLC myseq 2, mineseen 0, yourseen  
0, line down
*Jan 23 22:30:51.391: %LINEPROTO-5-UPDOWN: Line protocol on Interface  
Serial0/0/0, changed state to down
*Jan 23 22:31:00.391: Serial0/0/0: HDLC myseq 3, mineseen 0, yourseen  
0, line down
*Jan 23 22:31:10.391: Serial0/0/0: HDLC myseq 4, mineseen 0, yourseen  
0, line down
*Jan 23 22:31:20.391: Serial0/0/0: HDLC myseq 5, mineseen 0, yourseen  
0, line down
*Jan 23 22:31:21.391: Serial0/0/0: attempting to restart
*Jan 23 22:31:21.391:  gt96k_mbrd_serial_mode_reg_init:: was DTE, now  
set to DTE
*Jan 23 22:31:21.391:  DTE idb->dte_interface = DTE
*Jan 23 22:31:21.391: Dscc4(Serial0/0/0): DCD is up.

*Jan 23 22:31:30.391: Serial0/0/0: HDLC myseq 6, mineseen 0, yourseen  
0, line down
*Jan 23 22:31:40.391: Serial0/0/0: HDLC myseq 7, mineseen 0, yourseen  
0, line down no deb all
All possible debugging has been turned off


If I plug the T1 circuit into a 1760 w- a V1 WIC-1DSU-T1, it comes  
right up...

Any ideas??

Joe

Joe McGuckin
ViaNet Communications

joe at via.net
650-207-0372 cell
650-213-1302 office
650-969-2124 fax