[c-nsp] Analog Dialer
Mad Unix
madunix at gmail.com
Wed Jul 9 05:25:25 EDT 2008
I have added this but it didnt help it keeps trying to connect to
authenticate then failed
SDC_R2#conf t
Enter configuration commands, one per line. End with CNTL/Z.
SDC_R2(config)#line 450 473
SDC_R2(config-line)#exec-timeout 0 0
SDC_R2(config-line)#modem Dialin
SDC_R2(config-line)#transport input all
SDC_R2(config-line)#autoselect during-login
SDC_R2(config-line)#autoselect ppp
SDC_R2(config-line)#
SDC_R2(config-line)#exit
SDC_R2(config)#exit
SDC_R2#sh line
Tty Line Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns
Int
0 0 CTY - - - - - 1 0
0/0 -
Ready
1 1 AUX 9600/9600 - - - - - 0 0
0/0 -
Ready
I 0/450 450 TTY - DialIn - - - 0 0
0/0 -
Idle
I 0/451 451 TTY - DialIn - - - 0 0
0/0 -
Idle
I 0/452 452 TTY - DialIn - - - 0 0
0/0 -
Idle
I 0/453 453 TTY - DialIn - - - 0 0
0/0 -
Idle
I 0/454 454 TTY - DialIn - - - 0 0
0/0 -
Idle
I 0/455 455 TTY - DialIn - - - 0 0
0/0 -
Idle
I 0/456 456 TTY - DialIn - - - 0 0
0/0 -
Idle
I 0/457 457 TTY - DialIn - - - 0 0
0/0 -
Idle
I 0/458 458 TTY - DialIn - - - 0 0
0/0 -
Idle
I 0/459 459 TTY - DialIn - - - 0 0
0/0 -
Idle
I 0/460 460 TTY - DialIn - - - 0 0
0/0 -
Idle
I 0/461 461 TTY - DialIn - - - 0 0
0/0 -
Idle
I 0/462 462 TTY - DialIn - - - 0 0
0/0 -
Idle
I 0/463 463 TTY - DialIn - - - 0 0
0/0 -
Idle
I 0/464 464 TTY - DialIn - - - 0 0
0/0 -
Idle
I 0/465 465 TTY - DialIn - - - 0 0
0/0 -
Idle
I 0/466 466 TTY - DialIn - - - 0 0
0/0 -
Idle
I 0/467 467 TTY - DialIn - - - 0 0
0/0 -
Idle
I 0/468 468 TTY - DialIn - - - 0 0
0/0 -
Idle
I 0/469 469 TTY - DialIn - - - 0 0
0/0 -
Idle
I 0/470 470 TTY - DialIn - - - 0 0
0/0 -
Idle
I 0/471 471 TTY - DialIn - - - 0 0
0/0 -
Idle
I 0/472 472 TTY - DialIn - - - 0 0
0/0 -
Idle
I 0/473 473 TTY - DialIn - - - 0 0
0/0 -
Idle
* 706 706 VTY - - - - - 50 0
0/0 -
Ready
* 707 707 VTY - - - - - 9 0
0/0 -
Ready
708 708 VTY - - - - - 1 0
0/0 -
Ready
709 709 VTY - - - - - 0 0
0/0 -
Idle
710 710 VTY - - - - - 0 0
0/0 -
Idle
Line(s) not in async mode -or- with no hardware support:
2-449, 474-705
regarding the CEF we have disabled becuase it was disconnecting the Dialer
after atime...
so we added this no ip route-cache cef
interface Serial4/0:15
no ip address
encapsulation ppp
no ip route-cache cef
dialer rotary-group 1
dialer-group 2
isdn switch-type primary-net5
isdn incoming-voice modem
isdn guard-timer 3000
!
interface Serial4/1:15
no ip address
encapsulation ppp
no ip route-cache cef
dialer rotary-group 1
dialer-group 1
isdn switch-type primary-net5
isdn incoming-voice modem
isdn guard-timer 3000
!
On Wed, Jul 9, 2008 at 11:05 AM, Oliver Boehmer (oboehmer) <
oboehmer at cisco.com> wrote:
> some patience, please :-) .. we all do this in our spare time..
>
> The "line" config is missing (i.e. the lower part of the config). can you
> send this as well?
> Please re-enable CEF on the serial interface ("ip route-cache cef")
>
> oli
>
> ------------------------------
> *From:* Mad Unix [mailto:madunix at gmail.com]
> *Sent:* Wednesday, July 09, 2008 10:31 AM
> *To:* Oliver Boehmer (oboehmer)
> *Cc:* cisco-nsp at puck.nether.net
> *Subject:* Re: [c-nsp] Analog Dialer
>
> Any updates
>
> On Wed, Jul 9, 2008 at 9:05 AM, Mad Unix <madunix at gmail.com> wrote:
>
>> Am using interface Group-Async1 to accept analog calls for data transfer
>>
>>
>> interface GigabitEthernet0/0
>> description $ES_LAN$
>> ip address 10.16.0.2 255.255.255.0
>> duplex auto
>> speed auto
>> media-type rj45
>> !
>> interface GigabitEthernet0/1
>> ip address 10.16.1.2 255.255.255.0
>> duplex auto
>> speed auto
>> media-type rj45
>> !
>> interface Serial0/0/0
>> description ---- Elect ----
>> ip address 10.14.11.5 255.255.255.252
>> !
>> interface Serial0/0/1
>> description --- Bank ---
>> ip address 10.14.11.1 255.255.255.252
>> encapsulation ppp
>>
>> interface Serial4/0:15
>> no ip address
>> encapsulation ppp
>> no ip route-cache cef
>> dialer rotary-group 1
>> dialer-group 2
>> isdn switch-type primary-net5
>> isdn incoming-voice modem
>> isdn guard-timer 3000
>> !
>> interface Serial4/1:15
>> no ip address
>> encapsulation ppp
>> no ip route-cache cef
>> dialer rotary-group 1
>> dialer-group 1
>> isdn switch-type primary-net5
>> isdn incoming-voice modem
>> isdn guard-timer 3000
>> !
>> interface Dialer1
>> description connected to Dial-inPCs(ISDN)
>> ip address 10.13.1.1 255.255.255.0
>> encapsulation ppp
>> no ip split-horizon
>> dialer in-band
>> dialer idle-timeout 3600
>> dialer-group 1
>> peer default ip address pool Cisco3662-Group-1
>> ppp authentication chap pap ms-chap callin
>> !
>> interface Group-Async1
>> description connected tp Dial-in pcs (Analog)
>> ip unnumbered GigabitEthernet0/0
>> encapsulation ppp
>> no ip split-horizon
>> dialer in-band
>> dialer idle-timeout 3600
>> dialer-group 1
>> async mode interactive
>> peer default ip address pool cisco3662-group-2
>> no fair-queue
>> ppp authentication chap pap ms-chap callin
>> group-range 0/450 0/473
>> ip http server
>> ip http authentication local
>> ip http timeout-policy idle 60 life 86400 requests 10000
>> !
>> ip radius source-interface GigabitEthernet0/0
>> access-list 2 permit 10.5.0.0 0.0.255.255
>> access-list 100 permit ip 10.4.0.0 0.0.255.255 10.13.0.0 0.0.255.255
>> access-list 100 permit ip 10.5.0.0 0.0.255.255 10.13.0.0 0.0.255.255
>> access-list 100 permit ip 10.5.0.0 0.0.255.255 10.0.0.0 0.255.255.255
>> access-list 101 permit tcp host 10.5.3.10 any eq telnet
>> dialer-list 1 protocol ip permit
>> dialer-list 2 protocol ip permit
>>
>>
>> On Wed, Jul 9, 2008 at 8:39 AM, Oliver Boehmer (oboehmer) <
>> oboehmer at cisco.com> wrote:
>>
>>> Can't tell based on this config alone. can you please show the full
>>> config? (at least the one of the Serialx/y:z (the D-channel), any dialer
>>> interfaces and the "line" config at the end)?
>>> http://www.cisco.com/en/US/products/hw/univgate/ps505/products_configura
>>> tion_example09186a0080094a49.shtml shows a sample AS5xxx config, which
>>> can easily be adapted to your environment..
>>>
>>> oli
>>>
>>>
>>> Mad Unix <> wrote on Wednesday, July 09, 2008 8:27 AM:
>>>
>>> > have a PRI connecting 60 ppl using BRI and Analog calls
>>> > the Router 3800 PRI interface is having Digital modem to accept
>>> > analog phone calls
>>> > the analog callers cant connect!
>>> > What could be wrong?
>>> >
>>> > interface Group-Async1
>>> > description connected tp Dial-in pcs (Analog)
>>> > ip unnumbered GigabitEthernet0/0
>>> > encapsulation ppp
>>> > no ip split-horizon
>>> > dialer in-band
>>> > dialer idle-timeout 3600
>>> > dialer-group 1
>>> > async mode interactive
>>> > peer default ip address pool cisco3662-group-2
>>> > no fair-queue
>>> > ppp authentication chap pap ms-chap callin
>>> > group-range 0/450 0/473
>>> > --
>>> > madunix
>>> > _______________________________________________
>>> > cisco-nsp mailing list cisco-nsp at puck.nether.net
>>> > https://puck.nether.net/mailman/listinfo/cisco-nsp
>>> > archive at http://puck.nether.net/pipermail/cisco-nsp/
>>>
>>
>>
>>
>> --
>> madunix
>
>
>
>
> --
> madunix
>
--
madunix
More information about the cisco-nsp
mailing list