[c-nsp] 6509 noob question

[Adam Greene]

I just confirmed that those two commands are not available in Hybrid mode.

Thanks,
adam

----- Original Message ----- 
From: "David Prall" <dcp at dcptech.com>
To: "'Tassos Chatzithomaoglou'" <achatz at forthnet.gr>
Cc: "'Adam Greene'" <maillist at webjogger.net>; <cisco-nsp at puck.nether.net>
Sent: Wednesday, March 26, 2008 8:20 AM
Subject: RE: [c-nsp] 6509 noob question


Those are both commands available in Native IOS. I don't know if they are
available in Hybrid, although it would be nice to know if they were.

--
http://dcp.dcptech.com


> -----Original Message-----
> From: Tassos Chatzithomaoglou [mailto:achatz at forthnet.gr]
> Sent: Wednesday, March 26, 2008 6:40 AM
> To: David Prall
> Cc: 'Adam Greene'; cisco-nsp at puck.nether.net
> Subject: Re: [c-nsp] 6509 noob question
>
> The following two could probably help you too:
>
> remote command switch xxx
> remote login switch
>
> --
> Tassos
>
>
> David Prall wrote on 25/3/2008 11:05 μμ:
> > Switch console can only be done from catos. You want to
> find and entry that
> > has a mac address within the cisco range. What does "sh cdp
> neighbor" give
> > you. I don't remember this working, but it has been a long
> time. Then "sh
> > cdp neighbor detail" for the address. Might get lucky.
> >
> > David
> >
> > --
> > http://dcp.dcptech.com
> >
> >
> >> -----Original Message-----
> >> From: Adam Greene [mailto:maillist at webjogger.net]
> >> Sent: Tuesday, March 25, 2008 4:58 PM
> >> To: David Prall; cisco-nsp at puck.nether.net
> >> Subject: Re: [c-nsp] 6509 noob question
> >>
> >> Thanks, all.
> >>
> >> Neither the session nor switch console commands are
> >> recognized on the IOS
> >> side.
> >>
> >> Is there anything specific I should look for in the ARP
> >> table? There are
> >> about 1000 entries in there.
> >>
> >> I guess next step will be to call this switch's admin ....
> >>
> >> thanks,
> >> Adam
> >>
> >> ----- Original Message ----- 
> >> From: "David Prall" <dcp at dcptech.com>
> >> To: "'Adam Greene'" <maillist at webjogger.net>;
> >> <cisco-nsp at puck.nether.net>
> >> Sent: Tuesday, March 25, 2008 4:45 PM
> >> Subject: RE: [c-nsp] 6509 noob question
> >>
> >>
> >>> You need the management interface address for the catos
> >> side, from their
> >>> you
> >>> can session to the msfc/msfc's. Can telnet from the msfc to
> >> the catos side
> >>> if you know the address. Might be able to figure out where
> >> it is from the
> >>> arp table.
> >>>
> >>> David
> >>>
> >>> --
> >>> http://dcp.dcptech.com
> >>>
> >>>
> >>>> -----Original Message-----
> >>>> From: cisco-nsp-bounces at puck.nether.net
> >>>> [mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of
> Adam Greene
> >>>> Sent: Tuesday, March 25, 2008 4:20 PM
> >>>> To: cisco-nsp at puck.nether.net
> >>>> Subject: [c-nsp] 6509 noob question
> >>>>
> >>>> How's this for a stupid question?
> >>>>
> >>>> I'm working remotely on a pair of 6509's: CatOS 8.3(3) / IOS
> >>>> 12.1(8a)E3.
> >>>>
> >>>> I can telnet to the devices and access the IOS CLI.
> >>>>
> >>>> The million-dollar question: how to I access the CatOS CLI?
> >>>>
> >>>> As far as I can tell all the switch configs live in CatOS
> >>>> while the routing configs live in IOS, and I'm trying to gain
> >>>> access to the spanning-tree info (CatOS), to see if the
> >>>> switch is running PVST+, MST or what.
> >>>>
> >>>> Thanks,
> >>>> Adam
> >>>> _______________________________________________
> >>>> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> >>>> https://puck.nether.net/mailman/listinfo/cisco-nsp
> >>>> archive at http://puck.nether.net/pipermail/cisco-nsp/
> >>>
> >>>
> >>>
> >>>
> >>>
> >>
> >>
> >>
> >
> > _______________________________________________
> > cisco-nsp mailing list  cisco-nsp at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-nsp
> > archive at http://puck.nether.net/pipermail/cisco-nsp/
> >