[c-nsp] ALARM CARD ERROR

[jack daniels]

Hi All

I'm getting below error on GSR 12416 ALARM CARD -

IOS 12.0(32)SY6



WARNING: Unknown MBUS agent controller type, slot 24
Contact your technical support
representative.<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<Please advise



sh diag 24

SLOT 24 (ALM 0   ): Alarm Module(16)
  MAIN: type 64,  800-5570-05 rev C0
        Deviation: 0
        HW config: 0x00    SW key: 00-00-00
  PCA:  73-4266-04 rev B0 ver 3
        Design Release 1.0  S/N SAL1250CZJ9
  MBUS: Unknown (0)  00-0000-00 rev 70 dev 0
        HW version 1.2  S/N SAL1248BSQ5
        Test hist: 0x00    RMA#: 00-00-00    RMA hist: 0x00
  DIAG: Test count: 0x00000000    Test results: 0x00000000
  FRU:  Linecard/Module: GSR16-ALRM=
  MBUS Agent Software version 2.68 (RAM) (ROM version is 3.66)




sh gsr
Slot 0  type  = Modular SPA Interface Card
        state = IOS RUN   Line Card Enabled
        subslot 0/0: SPA-1X10GE-L-V2 (0x50C), status is ok
        subslot 0/1: Empty
        subslot 0/2: Empty
        subslot 0/3: Empty
Slot 5  type  = Modular SPA Interface Card
        state = IOS RUN   Line Card Enabled
        subslot 5/0: SPA-2XOC48POS/RPR (0x46F), status is ok
        subslot 5/1: SPA-5X1GE-V2 (0x50A), status is ok
        subslot 5/2: Empty
        subslot 5/3: Empty
Slot 6  type  = Modular SPA Interface Card
        state = IOS RUN   Line Card Enabled
        subslot 6/0: SPA-4XT3/E3 (0x40B), status is ok
        subslot 6/1: SPA-4XT3/E3 (0x40B), status is ok
        subslot 6/2: SPA-8XOC3-POS (0x505), status is ok
        subslot 6/3: SPA-8XOC3-POS (0x505), status is ok
Slot 7  type  = Performance Route Processor
        state = ACTV RP   IOS Running  ACTIVE
Slot 8  type  = Performance Route Processor
        state = STBY RP   IOS Running  STANDBY
Slot 9  type  = Modular SPA Interface Card
        state = IOS RUN   Line Card Enabled
        subslot 9/0: SPA-1X10GE-L-V2 (0x50C), status is ok
        subslot 9/1: Empty
        subslot 9/2: Empty
        subslot 9/3: Empty
Slot 14 type  = Modular SPA Interface Card
        state = IOS RUN   Line Card Enabled
        subslot 14/0: SPA-2XOC48POS/RPR (0x46F), status is ok
        subslot 14/1: SPA-5X1GE-V2 (0x50A), status is ok
        subslot 14/2: Empty
        subslot 14/3: Empty
Slot 15 type  = Modular SPA Interface Card
        state = IOS RUN   Line Card Enabled
        subslot 15/0: SPA-4XOC12-POS (0x507), status is ok
        subslot 15/1: SPA-8XOC3-POS (0x505), status is ok
        subslot 15/2: SPA-4XT3/E3 (0x40B), status is ok
        subslot 15/3: Empty
Slot 16 type  = Clock Scheduler Card OC192 Dual Priority
        state = Card Powered
Slot 17 type  = Clock Scheduler Card OC192 Dual Priority
        state = Card Powered  PRIMARY CLOCK
Slot 18 type  = Switch Fabric Card 16XOC192
        state = Card Powered
Slot 19 type  = Switch Fabric Card 16XOC192
        state = Card Powered
Slot 20 type  = Switch Fabric Card 16XOC192
        state = Card Powered
Slot 24 type  = Alarm Module(16)
        state = Card Powered
Slot 25 type  = Alarm Module(16)
        state = Card Powered
Slot 27 type  = Bus Board(16)
        state = Card Powered
Slot 28 type  = Blower Module(16)
        state = Card Powered
Slot 29 type  = Blower Module(16)
        state = Card Powered


Thanks and Regards
J.Daniels