[c-nsp] ALARM CARD ERROR

[jack daniels]

Hi,

opened just tac case and as per them its a hardware isssue .

Thanks and Regards
J.Daniels


On 8/10/09, Aaron <dudepron at gmail.com> wrote:
>
> Open a tac case.
>
>  On Mon, Aug 10, 2009 at 00:55, jack daniels <jckdaniels12 at gmail.com>wrote:
>
>> Hi All
>>
>> I'm getting below error on GSR 12416 ALARM CARD -
>>
>> IOS 12.0(32)SY6
>>
>>
>>
>> WARNING: Unknown MBUS agent controller type, slot 24
>> Contact your technical support
>> representative.<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<Please advise
>>
>>
>>
>> sh diag 24
>>
>> SLOT 24 (ALM 0   ): Alarm Module(16)
>>  MAIN: type 64,  800-5570-05 rev C0
>>        Deviation: 0
>>        HW config: 0x00    SW key: 00-00-00
>>  PCA:  73-4266-04 rev B0 ver 3
>>        Design Release 1.0  S/N SAL1250CZJ9
>>  MBUS: Unknown (0)  00-0000-00 rev 70 dev 0
>>        HW version 1.2  S/N SAL1248BSQ5
>>        Test hist: 0x00    RMA#: 00-00-00    RMA hist: 0x00
>>  DIAG: Test count: 0x00000000    Test results: 0x00000000
>>  FRU:  Linecard/Module: GSR16-ALRM=
>>  MBUS Agent Software version 2.68 (RAM) (ROM version is 3.66)
>>
>>
>>
>>
>> sh gsr
>> Slot 0  type  = Modular SPA Interface Card
>>        state = IOS RUN   Line Card Enabled
>>        subslot 0/0: SPA-1X10GE-L-V2 (0x50C), status is ok
>>        subslot 0/1: Empty
>>        subslot 0/2: Empty
>>        subslot 0/3: Empty
>> Slot 5  type  = Modular SPA Interface Card
>>        state = IOS RUN   Line Card Enabled
>>        subslot 5/0: SPA-2XOC48POS/RPR (0x46F), status is ok
>>        subslot 5/1: SPA-5X1GE-V2 (0x50A), status is ok
>>        subslot 5/2: Empty
>>        subslot 5/3: Empty
>> Slot 6  type  = Modular SPA Interface Card
>>        state = IOS RUN   Line Card Enabled
>>        subslot 6/0: SPA-4XT3/E3 (0x40B), status is ok
>>        subslot 6/1: SPA-4XT3/E3 (0x40B), status is ok
>>        subslot 6/2: SPA-8XOC3-POS (0x505), status is ok
>>        subslot 6/3: SPA-8XOC3-POS (0x505), status is ok
>> Slot 7  type  = Performance Route Processor
>>        state = ACTV RP   IOS Running  ACTIVE
>> Slot 8  type  = Performance Route Processor
>>        state = STBY RP   IOS Running  STANDBY
>> Slot 9  type  = Modular SPA Interface Card
>>        state = IOS RUN   Line Card Enabled
>>        subslot 9/0: SPA-1X10GE-L-V2 (0x50C), status is ok
>>        subslot 9/1: Empty
>>        subslot 9/2: Empty
>>        subslot 9/3: Empty
>> Slot 14 type  = Modular SPA Interface Card
>>        state = IOS RUN   Line Card Enabled
>>        subslot 14/0: SPA-2XOC48POS/RPR (0x46F), status is ok
>>        subslot 14/1: SPA-5X1GE-V2 (0x50A), status is ok
>>        subslot 14/2: Empty
>>        subslot 14/3: Empty
>> Slot 15 type  = Modular SPA Interface Card
>>        state = IOS RUN   Line Card Enabled
>>        subslot 15/0: SPA-4XOC12-POS (0x507), status is ok
>>        subslot 15/1: SPA-8XOC3-POS (0x505), status is ok
>>        subslot 15/2: SPA-4XT3/E3 (0x40B), status is ok
>>        subslot 15/3: Empty
>> Slot 16 type  = Clock Scheduler Card OC192 Dual Priority
>>        state = Card Powered
>> Slot 17 type  = Clock Scheduler Card OC192 Dual Priority
>>        state = Card Powered  PRIMARY CLOCK
>> Slot 18 type  = Switch Fabric Card 16XOC192
>>        state = Card Powered
>> Slot 19 type  = Switch Fabric Card 16XOC192
>>        state = Card Powered
>> Slot 20 type  = Switch Fabric Card 16XOC192
>>        state = Card Powered
>> Slot 24 type  = Alarm Module(16)
>>        state = Card Powered
>> Slot 25 type  = Alarm Module(16)
>>        state = Card Powered
>> Slot 27 type  = Bus Board(16)
>>        state = Card Powered
>> Slot 28 type  = Blower Module(16)
>>        state = Card Powered
>> Slot 29 type  = Blower Module(16)
>>        state = Card Powered
>>
>>
>> Thanks and Regards
>> J.Daniels
>> _______________________________________________
>> cisco-nsp mailing list  cisco-nsp at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/cisco-nsp
>> archive at http://puck.nether.net/pipermail/cisco-nsp/
>>
>
>