[c-nsp] Reload without confirmation

[David Freedman]

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Yes, unfortunately it does take the command but alas does not work:

Router(config)#snmp-server system-shutdown
Router(config)#end
Router#
Router#sh run | in shutdown
snmp-server system-shutdown

$ snmpset -v2c -c private 10.0.0.2 1.3.6.1.4.1.9.2.9.9.0 i 2
Error in packet.
Reason: noCreation (That table does not support row creation or that
object can not ever be created)
Failed object: SNMPv2-SMI::enterprises.9.2.9.9.0

$ snmpwalk -v2c -c private 10.0.0.2 .1.3.6.1.4.1.9.2.9
SNMPv2-SMI::enterprises.9.2.9 = No Such Object available on this agent
at this OID

Router# sh ver
Cisco IOS Software, C870 Software (C870-ADVIPSERVICESK9-M), Version
12.4(20)T1, RELEASE SOFTWARE (fc3)

so using modern 12.4(T) and ADVIP image , perhaps I'm using outdated MIB?

Dave.


Brian Turnbow wrote:
> In the past I used snmp dto do this, you need to enable
> snmp-server system-shutdown 
> Before it is possible, and it is not possible on all platforms, but is it takes this command it should work
> I don't have the mib handy , but can dig for it if you can't find it
> 
> 
> Brian  
> 
> 
> -----Original Message-----
> From: cisco-nsp-bounces at puck.nether.net [mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of David Freedman
> Sent: mercoledì 24 giugno 2009 15.11
> To: Jared Mauch; 'Cisco-nsp'
> Subject: Re: [c-nsp] Reload without confirmation
> 
> No, same problem :
> 
> #reload at 01:00
> Reload scheduled for 01:00:00 BST Thu Jun 25 2009 (in 10 hours and 50
> minutes) by user on vty0 (10.0.0.1)
> Reload reason: Reload Command
> Proceed with reload? [confirm]
> 
> #reload in 5
> Reload scheduled for 14:15:10 BST Wed Jun 24 2009 (in 5 minutes) by
> user on vty0 (10.0.0.1)
> Reload reason: Reload Command
> Proceed with reload? [confirm]
> 
> Dave.
> 
> Jared Mauch wrote:
>> You can't use reload at to meet your needs?
> 
>> Jared Mauch
> 
>> On Jun 24, 2009, at 8:25 AM, David Freedman
>> <david.freedman at uk.clara.net> wrote:
> 
>>> Am trying to reload a low end IOS device (c800 in this case) without
>>> displaying a confirmation prompt.
>>>
>>> My issue is that the platform needing to issue the command can not "see"
>>> the VTY output so could not be expected to respond to a confirmation
>>> prompt, looked in vain for some kind of "/noconfirm" flag but didn't
>>> find one...
>>>
>>> Does not appear to be possible with SNMP (even though it accepts the
>>> snmp-server shutdown command).
>>>
>>> My current solution is to use an EEM applet called manually with a
>>> single action of "reload" , unfortunately this only applies to 800
>>> images with EEM (I would guess ADV images only)
>>>
>>> Anybody come up with a better solution?
>>>
>>> TIA
>>>
>>> Dave.
>>>
>>> _______________________________________________
>>> cisco-nsp mailing list  cisco-nsp at puck.nether.net
>>> https://puck.nether.net/mailman/listinfo/cisco-nsp
>>> archive at http://puck.nether.net/pipermail/cisco-nsp/
> 
_______________________________________________
cisco-nsp mailing list  cisco-nsp at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)
Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org

iEYEARECAAYFAkpCMkMACgkQtFWeqpgEZrJtBQCg1GyFyviPBeBATJK4NVfGCQtZ
EWYAoImBYeLufvWu5/VciSpFBAAjVwBM
=B9D1
-----END PGP SIGNATURE-----