[c-nsp] Sup720 crashing at RP boot - HW revision dependent ?

Marcus.Gerdon Marcus.Gerdon at versatel.de
Wed Mar 11 08:05:20 EDT 2009


Tassos,

they've been delivered and supplier-tested with 8.4(2) and 12.2(17r)S4 and bootet with those smoothly in the 6506.

I'm running 8.5(1) and 12.2(17r)SX5 everywhere and updated those Sup's accordingly. But it didn't make difference.



regards,

Marcus
 

> -----Ursprüngliche Nachricht-----
> Von: cisco-nsp-bounces at puck.nether.net 
> [mailto:cisco-nsp-bounces at puck.nether.net] Im Auftrag von 
> Tassos Chatzithomaoglou
> Gesendet: Mittwoch, 11. März 2009 12:25
> An: cisco-nsp at puck.nether.net
> Betreff: Re: [c-nsp] Sup720 crashing at RP boot - HW revision 
> dependent ?
> 
> Marcus, are you using the latest rommon in the SP (8.5(3)) 
> and RP (12.2(17r)SX5)?
> 
> 6500#remote command switch sh ver | i ROM:
> ROM: System Bootstrap, Version 8.5(3)
> 
> 6500#sh ver | i ROM:
> ROM: System Bootstrap, Version 12.2(17r)SX5, RELEASE SOFTWARE (fc1)
> 
> 
> -- 
> Tassos
> 
> 
> Marcus.Gerdon wrote on 11/03/2009 12:45:
> > Hi @all,
> > 
> > yesterday I've been hit by a somewhat strange - and 
> possibly worrying -
> > effect with Sup720 in 6500.
> > 
> > I've got 3 Sup720-3BXL, one with an older HW revision (Sup: 
> 4.4 / PFC:
> > 1.6 / MSFC: 2.5) and 2 with newer (Sup: 5.2 / PFC: 1.8 / 
> MSFC: 2.5). All
> > three have been tested in a 6509 successfully by the 
> supplier. According
> > the test sheets they've used a Rev. 3.0 chassis.
> > 
> > For offline testing and preparation I've an 6509 and 6506 
> spare chassis
> > at hands, both of them being Rev. 2.0.
> > 
> > When trying to boot those Sup in my 6509 the older one 
> boots fine and
> > everything is ok. The newer ones both start to boot and 
> after switching
> > to boot the RP it stalls (download doesn't even start, hangs after
> > memory is displayed). After a minute or two a 'software 
> forced crash'
> > occurs and I'm thrown do SP rommon.
> > 
> > Up to this point no updates, config changes or anything other than
> > plugging them in the chassis and turning the power on has been done.
> > 
> > It doesn't matter if they're put in slot 5 or 6, if the 
> working one is
> > already active in slot 5 or if I'm manually booting from 
> rommon instead
> > of autoboot. Also the IOS used doesn't change anything 
> (18SXF, 18SXI,
> > 17SXd)
> > 
> > Interestingly in the Rev. 2.0 6506 all three are booting 
> fine. I've done
> > both rom updates in the 6506 and tried again in the 6509 - 
> without any
> > change.
> > 
> > To me this looks like there's some dependancy between HW 
> revisions of
> > the Sup or PFC (MSFC rev. is the same on all threee) and the 6509
> > chassis (6506 wasn't effected). 
> > 
> > I've searched cisco.com for quite some time but without any 
> hint to this
> > issue. The only thing I found was that there're a few 
> 6509-NEB eeprom
> > updates to be applied to the chassis itself. So in fact 
> there is some
> > active rom part with the chassis that supposedly will differ between
> > revisions.
> > 
> > 
> > Does someone stumbled upon this, had similar issues or 
> maybe even know
> > or did see any document (comp. matrix, workaround or alike) 
> about this ?
> > 
> > 
> > 
> > regards,
> > 
> > Marcus
> > _______________________________________________
> > cisco-nsp mailing list  cisco-nsp at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-nsp
> > archive at http://puck.nether.net/pipermail/cisco-nsp/
> > 
> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/
> 


More information about the cisco-nsp mailing list