[c-nsp] Etherchannel load balancing

[Ziv Leyes]

The link doesn't work because the whole line is broken in two, there is a missing part in the link that is continued in the line after.
Just copy/paste the whole text that starts at "http" and up to where it ends with ".shtml"
Ziv


-----Original Message-----
From: cisco-nsp-bounces at puck.nether.net [mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of Ivan ?imko
Sent: Thursday, June 24, 2010 4:41 PM
To: Billy Guthrie
Cc: cisco-nsp at puck.nether.net
Subject: Re: [c-nsp] Etherchannel load balancing

Hi Billy

thanks a lot. Can you send me that doc? Link isn't working :-(

Regards

Ivan

On 24 June 2010 14:16, Billy Guthrie <bg at billyguthrie.com> wrote:

> When you configure an etherchannel bundle, the frames are distributed
> across the individual bundled links deterministically; however, the load is
> not balanced equally across all the links. You may or may not know, but the
> frames are forwarded on a specific link due to the hashing algorithm that is
> used. The algorithm can use destination IP address, source IP address, or a
> combination of both source and destination IP addresses, source and
> destination MAC addresses, or TCP and UDP port numbers. The hashing
> algorithm computes a binary pattern that selects a link number in a bundle
> to carry each frame.
>
> Document may or may not help:
>
> http://www.cisco.com/en/US/tech/tk389/tk213/technologies_tech_note09186a0080094714.shtm
>
>
> Good Luck
> Billy
>
>
> Ivan Šimko wrote:
>
>> Hi all
>>
>> I've got two switches 3560
>> group with 2xFE on both switches and inteconnected together.
>> port channel is L2
>> 2 VRFs - ivan, mark
>> 4 VLANs:
>> - vlan 100 VRF "ivan" for interconnection between swtiches
>> - vlan 11 VRF "ivan" for customer's connection
>>
>> - vlan 200 VRF"mark" for interconnection between switches
>> - vlan 12 VRF "mark" for customer's connection
>>
>> ports 12 and 13 as trunks
>> - interconnection between switches
>>
>> OSPF runs over SVIs of 100 and 200.
>>
>> I'm strugling with load balancing:
>> when I setup port channel load balancing dst-ip switch does correct
>> balancing between interconnected vlans but not for customers' vlans.
>> - vlan 100 would use port 12 - switch interconnection
>> - vlan 200 would use port 13 - switch interconnection
>> - vlan 11 would use port 13 - customer 1
>> - vlan 12 would use port 13 - customer 2
>>
>> when I setup port channel load balancing src-dst-ip switch does correct
>> balance for customers' vlans but not for interconnected vlans.
>> - vlan 100 would use port 13
>> - vlan 200 would use port 13
>> - vlan 11 would use port 12
>> - vlan 12 would use port 13
>>
>> Result is not full bandwidth used for both customers' traffic resp. only
>> 100
>> Mbps.
>>
>>
>> Any ideas how to sort it out?
>>
>> thanks
>> _______________________________________________
>> cisco-nsp mailing list  cisco-nsp at puck.nether.net
>> https://puck.nether.net/mailman/listinfo/cisco-nsp
>> archive at http://puck.nether.net/pipermail/cisco-nsp/
>>
>>
>>
>
>
_______________________________________________
cisco-nsp mailing list  cisco-nsp at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
 
 
************************************************************************************
This footnote confirms that this email message has been scanned by
PineApp Mail-SeCure for the presence of malicious code, vandals & computer viruses.
************************************************************************************


 
 
************************************************************************************
This footnote confirms that this email message has been scanned by
PineApp Mail-SeCure for the presence of malicious code, vandals & computer viruses.
************************************************************************************