[c-nsp] 7204VXR rebooted by watchdog hard reset with PA-FE in slot 1

Youssef Bengelloun-Zahr youssef at 720.fr
Mon Mar 8 10:42:42 EST 2010


Hello community,

I received a 7204VXR chassis with a I/O controler (no FE ports on it) et
plugged in it an old NPE-400 plus 2 PA-FE.

PA-FE 1 in in slot 1.

PA-FE 2 is in slot 2.

Upgraded my bootloader with c7200-boot-mz.120-22.S.bin and my version of IOS
is c7200-adventerprisek9-mz.122-33.SRD.bin.

Here is my problem :

When PA-FE1 is in slot1, the router loops during boot and the following
appears :

*Mar  8 05:20:09.459: %SYS-5-RELOAD: Reload requested by console. Reload
Reason: Reload command.
System Bootstrap, Version 12.2(4r)B, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2002 by cisco Systems, Inc.
C7200 platform with 524288 Kbytes of main memory


Self decompressing the image :
###########################################################################################################################################################################################################]

%SYS-4-CONFIG_NEWER: Configuration from version 12.2 may not be correctly
understood
%DEC21140-5-NOCARR: FastEthernet1/0 cable/connector problem?
%DEC21140-5-NOCARR: FastEthernet1/0 cable/connector problem?
%DEC21140-5-NOCARR: FastEthernet1/0 cable/connector problem?
%SYS-6-BOOT_MESSAGES: Messages above this line are from the boot loader.
Self decompressing the image :
###########################################################################################################################################################################################################]

System Bootstrap, Version 12.2(4r)B, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2002 by cisco Systems, Inc.

*ROM: Rebooted by watchdog hard reset
*C7200 platform with 524288 Kbytes of main memory


When I remove the PA-FE from slot 1 or insert it in another slot (2,3 or 4),
everything works like a charm. Moreover, swapping with another PA-FE in
slot1 causes the same problem !?!

Here is a sh controller of the PA-FE in question (but inserted in slot 3) :

Interface FastEthernet3/0
Hardware is DEC21140
 dec21140_ds=0x65948454, registers=0x3D800000, ib=0xE179D40
 rx ring entries=128, tx ring entries=256, af setup failed=0
 rxring=0x7E179E40, rxr shadow=0x65948A38, rx_head=0, rx_tail=0
 txring=0x7E17A680, txr shadow=0x65948C6C, tx_head=2, tx_tail=2, tx_count=0
 PHY link up
 CSR0=0xFFFA9082, CSR3=0xE179E40, CSR4=0xE17A680, CSR5=0xFC000000
 CSR6=0xE0000000, CSR7=0xFFFE0000, CSR8=0xFFFE0000, CSR9=0xFFFDD7FF
 CSR11=0xFFFE0000, CSR12=0xFFFFFF09, CSR15=0xFFFFFEC8
 TX state: stopped
 RX state: stopped - RESET or STOP RECEIVE command
 Far End Fault Indication (For FX Interface): OFF
 DEC21140 PCI registers:
  bus_no=6, device_no=0
  CFID=0x00091011, CFCS=0x02800006, CFRV=0x02000012, CFLT=0x0000FF00
  CBIO=0xDFEFFF81, CBMA=0x49000000, CFIT=0x000001D1, CFDA=0x0000EF00
 MII registers:
  Register 0x00:   0400  784B  2000  5C01  0081  0000  0000  0000
  Register 0x08:   0000  0000  0000  0000  0000  0000  0000  0000
  Register 0x10:   0000  0000  0000  0000        0000  0001  8060
  Register 0x18:   8020  0800  0000  3800  A3B9
 Software MAC address filter(hash:length/addr/mask/hits):
 need_af_check = 0
  0x00:  0  ffff.ffff.ffff  0000.0000.0000         0
  0x10:  0  0009.443e.8854  0000.0000.0000         0
 throttled=0, enabled=0, disabled=0
 rx_fifo_overflow=0, rx_no_enp=0, rx_state=0
 tx_underrun_err=0, tx_jabber_timeout=0, tx_carrier_loss=1
 tx_no_carrier=0, tx_late_collision=0, tx_excess_coll=0
 tx_collision_cnt=0, tx_deferred=0, fatal_tx_err=0, tbl_overflow=0
 rx_pak_len_err = 0, filtered_pak_cnt = 0
 tx_limited=0(256)
 HW addr filter: 0xE18E700, ISL Disabled
  Entry= 0:  Addr=FFFF.FFFF.FFFF
  Entry= 1:  Addr=FFFF.FFFF.FFFF
  Entry= 2:  Addr=FFFF.FFFF.FFFF
  Entry= 3:  Addr=FFFF.FFFF.FFFF
  Entry= 4:  Addr=FFFF.FFFF.FFFF
  Entry= 5:  Addr=FFFF.FFFF.FFFF
  Entry= 6:  Addr=FFFF.FFFF.FFFF
  Entry= 7:  Addr=FFFF.FFFF.FFFF
  Entry= 8:  Addr=FFFF.FFFF.FFFF
  Entry= 9:  Addr=FFFF.FFFF.FFFF
  Entry=10:  Addr=FFFF.FFFF.FFFF
  Entry=11:  Addr=FFFF.FFFF.FFFF
  Entry=12:  Addr=FFFF.FFFF.FFFF
  Entry=13:  Addr=FFFF.FFFF.FFFF
  Entry=14:  Addr=FFFF.FFFF.FFFF
  Entry=15:  Addr=0009.443E.8854

I have been googling around but nothing very concluant so far.

Any clues ?

Thanks.

Best regards.

Cheers,

-- 
Youssef BENGELLOUN-ZAHR ………………………………………………
Ingénieur Réseaux et Télécoms


Technopole de l'Aube  en Champagne - BP 601 - 10901 TROYES  Cedex 9
Agence Paris : 6, rue Charles Floquet - 92120 MONTROUGE
Tel                 +33 (0) 825 000 720
Tel. direct      +33 (0) 1 77 35 59 14
Tel. portable  +33 (0) 6 22 42 63 80
Email            ybz at 720.fr
……………………………………………………………………………….....www.720.fr


More information about the cisco-nsp mailing list