[c-nsp] Replacing redundant Sup720 on Catalyst 6500
John Smith
jsmith19365 at yahoo.com
Fri Mar 26 08:45:33 EDT 2010
Greetings,
Thank you to all the engineers who responded to my query. I really appreciate all your help. I will take/review your suggestions and recommendations and plan our maintenance accordingly. Thanks again for all your help.
-John-
--- On Thu, 3/25/10, Peter Kranz <pkranz at unwiredltd.com> wrote:
From: Peter Kranz <pkranz at unwiredltd.com>
Subject: Re: [c-nsp] Replacing redundant Sup720 on Catalyst 6500
To: "'Youssef Bengelloun-Zahr'" <youssef at 720.fr>, "'Stephen Cobb'" <scobb at telecoast.com>
Cc: "'Cisco-nsp'" <cisco-nsp at puck.nether.net>
Date: Thursday, March 25, 2010, 8:17 PM
Also a chance of stalling the bus for too long if you insert the new
supervisor too slowly into the chassis.. so its possible you will reboot
even if you should not have to.
Peter Kranz
www.UnwiredLtd.com
Desk: 510-868-1614 x100
Mobile: 510-207-0000
pkranz at unwiredltd.com
-----Original Message-----
From: cisco-nsp-bounces at puck.nether.net
[mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of Youssef
Bengelloun-Zahr
Sent: Thursday, March 25, 2010 5:01 PM
To: Stephen Cobb
Cc: Cisco-nsp
Subject: Re: [c-nsp] Replacing redundant Sup720 on Catalyst 6500
Same old same.
FYI, this kind of problem is solved using UBL (in 12.2(33)SXI IOS I think).
Basicaly, during this kind of maitainance, the new module will download the
same IOS, config, etc... from the active one. I read that a few days ago,
comes in handy when you stand in the place you are in right now.
Good luck.
Y.
2010/3/26 Stephen Cobb <scobb at telecoast.com>
> John-
>
> You want it to boot the software you've already got up and running, so
> make a copy of the IOS onto some compact flash. When you insert the
> redundant Sup, have a console cable and terminal already connected so
> that you can monitor its boot process. Once you see the Sup's memory
> displayed,
> CTRL+BREAK and get to ROMMON. Then, tell it to boot that IOS you want
> CTRL+from
> the compact flash disk. If it boots correctly, you'll see console
> switch to its MSFC and then [once booted] it'll download the config
> from the active Sup and you'll be up and running. At that point,
> you'll want to move the console to your active Sup and make sure that
> your standby Sup's bootflash or bootdisk contains the IOS 12.2(18)SXF7
> that you want. If not, make the appropriate file copies from the active
Sup's bootflash or bootdisk. (i.e.
> copy sup-bootlfash:xxx.bin slavesup-bootflash:xxx.bin)
>
> That's the short...I'm sure those links would help as well.
>
> --
> Stephen F. Cobb • Senior Sales Engineer CCNA/CCDA/DCNID/CSE/ASP/ATSA
> Telecoast Communications, LLC • Santa Barbara, CA o 877.677.1182 x272
> • c 760.807.0570 • f 805.618.1610 aim/yahoo telecoaststephen
>
> On Thu, Mar 25, 2010 at 3:07 PM, John Smith <jsmith19365 at yahoo.com> wrote:
>
> > Greetings,
> >
> > To all who responded to my query ...
> >
> > Thank you for your responses. I appreciate it. I have couple more
> > questions.
> >
> > Do I need to do anything with the SSO or Redundancy config before I
> remove
> > the bad Sup module in Slot 5 and insert in the new module?
> >
> > The new module is coming from Cisco, so I have no idea what IOS it
> > will have on it. We do not have a spare chassis to stage the new
> > module coming from Cisco.
> >
> > Will the IOS and Config automatically sync with the Active module in
> > slot
> 6
> > when I insert the new/replacement module in slot 5.
> >
> > Thanks again for all your help. I very much appreciate it.
> >
> > Thanks!
> > -John-
> >
> > --- On Thu, 3/25/10, Youssef Bengelloun-Zahr <youssef at 720.fr> wrote:
> >
> >
> > From: Youssef Bengelloun-Zahr <youssef at 720.fr>
> > Subject: Re: [c-nsp] Replacing redundant Sup720 on Catalyst 6500
> > To: "John Smith" <jsmith19365 at yahoo.com>
> > Cc: cisco-nsp at puck.nether.net
> > Date: Thursday, March 25, 2010, 4:54 PM
> >
> >
> > P.S :
> >
> > As I said before, make sure you are replacing the STANDBY SUP, not
> > the active one (unless NSF is configured for your IGPs, etc...).
> >
> > Y.
> >
> >
> >
> >
> > 2010/3/25 Youssef Bengelloun-Zahr <youssef at 720.fr>
> >
> > Also, check out this :
> >
> >
> >
> http://www.cisco.com/en/US/products/hw/switches/ps708/products_configu
> ration_example09186a008086ed2e.shtml
> >
> > Y.
> >
> >
> >
> >
> > 2010/3/25 Youssef Bengelloun-Zahr <youssef at 720.fr>
> >
> >
> >
> >
> > Hello John,
> >
> > Based on your posting, the sup in slot 5 is in STANDBY state, so no
> worries
> > to have :-)
> >
> > FYI :
> >
> >
> >
> https://supportforums.cisco.com/docs/DOC-4068/version/1;jsessionid=667
> B4E9940D21005AC46FD72F7A602B9.node0
> >
> > Good luck !
> >
> > Y.
> >
> >
> >
> >
> > 2010/3/25 John Smith <jsmith19365 at yahoo.com>
> >
> >
> >
> >
> > We have a 6500 Switch in our network with two SUP720 engines running
> > in
> SSO
> > mode; one engine is Active and the other is in Standby Hot. The Sup
> engines
> > are in slot 5 and slot 6. We need to replace the card in Slot 5.
> >
> > Does anyone have a step by step procedure and/or web link on how to
> replace
> > the redundant supervisor card without rebooting the chassis.
> >
> > Any/all help is much appreciated. Thank you.
> >
> > We have the following config for the supervisors.
> >
> > !
> > redundancy
> > mode sso
> > main-cpu
> > auto-sync running-config
> > auto-sync standard
> > !
> >
> > Switch#show redundancy
> > Redundant System Information :
> > ------------------------------
> > Available system uptime = 2 year, 7 weeks, 3 days, 8 hours, 33
> > minutes Switchovers system experienced = 0
> > Standby failures = 0
> > Last switchover reason = none
> >
> > Hardware Mode = Duplex
> > Configured Redundancy Mode = sso
> > Operating Redundancy Mode = sso
> > Maintenance Mode = Disabled
> > Communications = Up
> >
> > Current Processor Information :
> > -------------------------------
> > Active Location = slot 6
> > Current Software state = ACTIVE
> > Uptime in current state = 2 year, 7 weeks, 3 days, 8 hours, 32
> > minutes
> > Image Version = Cisco Internetwork Operating System
> > Software IOS (tm) s72033_rp Software
> > (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(18)SXF7, RELEASE
> > SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport
> > Copyright (c) 1986-2006 by cisco Systems, Inc.
> > Compiled Thu 23-Nov-06 06:00 by kellythw
> > BOOT = disk0:,1;
> > CONFIG_FILE =
> > BOOTLDR =
> > Configuration register = 0x2102
> >
> > Peer Processor Information :
> > ----------------------------
> > Standby Location = slot 5
> > Current Software state = STANDBY HOT
> > Uptime in current state = 2 year, 7 weeks, 3 days, 8 hours, 32
> > minutes
> > Image Version = Cisco Internetwork Operating System
> > Software IOS (tm) s72033_rp Software
> > (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(18)SXF7, RELEASE
> > SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport
> > Copyright (c) 1986-2006 by cisco Systems, Inc.
> > Compiled Thu 23-Nov-06 06:00 by kellythw
> > BOOT = disk0:,1;
> > CONFIG_FILE =
> > BOOTLDR =
> > Configuration register = 0x2102
> >
> >
> > Thanks!
> > -John-
> >
> >
> >
> >
> > _______________________________________________
> > cisco-nsp mailing list cisco-nsp at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-nsp
> > archive at http://puck.nether.net/pipermail/cisco-nsp/
> >
> >
> >
> > --
> > Youssef BENGELLOUN-ZAHR ……………………………………………… Ingénieur Réseaux et
> > Télécoms
> >
> >
> > Technopole de l'Aube en Champagne - BP 601 - 10901 TROYES Cedex 9
> > Agence Paris : 6, rue Charles Floquet - 92120 MONTROUGE
> > Tel +33 (0) 825 000 720
> > Tel. direct +33 (0) 1 77 35 59 14
> > Tel. portable +33 (0) 6 22 42 63 80
> > Email ybz at 720.fr
> > ……………………………………………………………………………….....www.720.fr
> >
> >
> >
> >
> >
> >
> >
> > --
> > Youssef BENGELLOUN-ZAHR ……………………………………………… Ingénieur Réseaux et
> > Télécoms
> >
> >
> > Technopole de l'Aube en Champagne - BP 601 - 10901 TROYES Cedex 9
> > Agence Paris : 6, rue Charles Floquet - 92120 MONTROUGE
> > Tel +33 (0) 825 000 720
> > Tel. direct +33 (0) 1 77 35 59 14
> > Tel. portable +33 (0) 6 22 42 63 80
> > Email ybz at 720.fr
> > ……………………………………………………………………………….....www.720.fr
> >
> >
> >
> >
> > --
> > Youssef BENGELLOUN-ZAHR ……………………………………………… Ingénieur Réseaux et
> > Télécoms
> >
> >
> > Technopole de l'Aube en Champagne - BP 601 - 10901 TROYES Cedex 9
> > Agence Paris : 6, rue Charles Floquet - 92120 MONTROUGE
> > Tel +33 (0) 825 000 720
> > Tel. direct +33 (0) 1 77 35 59 14
> > Tel. portable +33 (0) 6 22 42 63 80
> > Email ybz at 720.fr
> > ……………………………………………………………………………….....www.720.fr
> >
> >
> >
> >
> >
> > _______________________________________________
> > cisco-nsp mailing list cisco-nsp at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-nsp
> > archive at http://puck.nether.net/pipermail/cisco-nsp/
> >
> _______________________________________________
> cisco-nsp mailing list cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/
>
--
Youssef BENGELLOUN-ZAHR ……………………………………………… Ingénieur Réseaux et Télécoms
Technopole de l'Aube en Champagne - BP 601 - 10901 TROYES Cedex 9
Agence Paris : 6, rue Charles Floquet - 92120 MONTROUGE
Tel +33 (0) 825 000 720
Tel. direct +33 (0) 1 77 35 59 14
Tel. portable +33 (0) 6 22 42 63 80
Email ybz at 720.fr
……………………………………………………………………………….....www.720.fr
_______________________________________________
cisco-nsp mailing list cisco-nsp at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
_______________________________________________
cisco-nsp mailing list cisco-nsp at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
More information about the cisco-nsp
mailing list