[c-nsp] Ethernet Interfaces Speed and Duplex - Force or Auto

[Rubens Kuhl]

Wherever possible I leave autoneg on but try to configure capabilities
to advertise only 100 (or 1000 or 100+1000) Full-Duplex. Operating
systems and some switch brands allow this, but since this is a Cisco
list I haven't found Cisco gear that allow this, so far.


Rubens


On Thu, May 20, 2010 at 4:18 PM, Jeff Wojciechowski
<Jeff.Wojciechowski at midlandpaper.com> wrote:
> All:
>
> Curious what other network admins are doing out there for Ethernet interfaces as far as speed and duplex settings - weather to specify or to leave them auto negotiate.
>
> The reason I am asking is we just installed some equipment in a new data center we are in the process of bringing online for redundancy and the switch ports on the network switch at the new location are set to 100/full while the switch this equipment was built and tested on in our main facility was set to auto/auto.
>
> Since equipment was moved to the new location I have been taking CRC errors on almost all active network ports that this equipment is plugged into yet the 3 months or so this system was in the other location with speed auto/duplex auto, we had none. I tried swapping out the network switch but I am still taking errors at about the same rate.
>
> Show int of port with most errors (WS-C3560-24TS)
>
> FastEthernet0/3 is up, line protocol is up (connected)
>  Hardware is Fast Ethernet, address is 001c.0f21.d085 (bia 001c.0f21.d085)
>  MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
>     reliability 255/255, txload 1/255, rxload 1/255
>  Encapsulation ARPA, loopback not set
>  Keepalive set (10 sec)
>  Full-duplex, 100Mb/s, media type is 10/100BaseTX
>  input flow-control is off, output flow-control is unsupported
>  ARP type: ARPA, ARP Timeout 04:00:00
>  Last input never, output 00:00:01, output hang never
>  Last clearing of "show interface" counters 1d18h
>  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
>  Queueing strategy: fifo
>  Output queue: 0/0 (size/max)
>  5 minute input rate 2000 bits/sec, 3 packets/sec
>  5 minute output rate 3000 bits/sec, 4 packets/sec
>     533310 packets input, 64455460 bytes, 0 no buffer
>     Received 5227 broadcasts (0 multicasts)
>     0 runts, 0 giants, 0 throttles
>     150 input errors, 69 CRC, 0 frame, 0 overrun, 0 ignored
>     0 watchdog, 0 multicast, 0 pause input
>     0 input packets with dribble condition detected
>     556098 packets output, 59830579 bytes, 0 underruns
>     0 output errors, 0 collisions, 0 interface resets
>     0 babbles, 0 late collision, 0 deferred
>     0 lost carrier, 0 no carrier, 0 PAUSE output
>     0 output buffer failures, 0 output buffers swapped out
>
> During non-production hours, I will be setting those ports to auto/auto to see if the errors go away - but still curious what others are doing - and does it depend on what sort of device is using a port such as a server, router, another switch, pc, etc?
>
> Thanks again,
>
> Jeff Wojciechowski
> LAN, WAN and Telephony Administrator
> Midland Paper Company
> 101 E Palatine Rd
> Wheeling, IL 60090
> * tel: 847.777.2829
> Ê fax: 847.403.6829
> e-mail: jeff.wojciechowski at midlandpaper.com<mailto:jeff.wojciechowski at midlandpaper.com>
> http://www.midlandpaper.com
>
> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/
>