[c-nsp] Installation of a PA-MC-2T1 in a 7206

[Josh Baird]

Forgive the silly question..

I just installed a PA-MC-2T1 in a 7206.  Logs confirm:

*Jul  5 19:17:20.519: %OIR-6-INSCARD: Card inserted in slot 5, interfaces
administratively shut down
*Jul  5 19:17:24.103: %ENTITY_ALARM-6-INFO: ASSERT INFO T15/0 Physical Port
Administrative State Down
*Jul  5 19:17:24.103: %ENTITY_ALARM-6-INFO: ASSERT INFO T15/1 Physical Port
Administrative State Down
*Jul  5 19:17:33.483: %ENTITY_ALARM-6-INFO: CLEAR INFO T15/0 Physical Port
Administrative State Down
*Jul  5 19:17:33.483: %ENTITY_ALARM-6-INFO: ASSERT MINOR T15/0 Physical Port
Link Down
*Jul  5 19:17:33.483: %ENTITY_ALARM-6-INFO: ASSERT MINOR T15/0 Transmitter
is sending remote alarm
*Jul  5 19:17:33.483: %ENTITY_ALARM-6-INFO: ASSERT MINOR T15/0 Receiver has
loss of signal
*Jul  5 19:17:33.483: %ENTITY_ALARM-6-INFO: CLEAR INFO T15/1 Physical Port
Administrative State Down
*Jul  5 19:17:33.483: %ENTITY_ALARM-6-INFO: ASSERT MINOR T15/1 Physical Port
Link Down
*Jul  5 19:17:33.483: %ENTITY_ALARM-6-INFO: ASSERT MINOR T15/1 Transmitter
is sending remote alarm
*Jul  5 19:17:33.483: %ENTITY_ALARM-6-INFO: ASSERT MINOR T15/1 Receiver has
loss of signal

sh diag confirms:

Slot 5:
        Channelized T1 (CSU) Port adapter, 2 ports
        Port adapter is analyzed
        Port adapter insertion time 00:22:26 ago
        EEPROM contents at hardware discovery:
        Hardware Revision        : 1.0
        Part Number              : 73-3927-02
        Board Revision           : C0
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        Deviation Number         : 0-0
        Product (FRU) Number     : PA-MC-2T1
        Top Assy. Part Number    : 800-04989-02
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF 40 01 77 41 01 00 C1 8B 4A 41 45 30 38 32
          0x10: 36 4D 56 55 37 82 49 0F 57 02 42 43 30 03 00 81
          0x20: 00 00 00 00 04 00 80 00 00 00 00 CB 94 50 41 2D
          0x30: 4D 43 2D 32 54 31 20 20 20 20 20 20 20 20 20 20
          0x40: 20 C0 46 03 20 00 13 7D 02 FF FF FF FF FF FF FF
          0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

According to docs on Cisco's site (
http://www.cisco.com/en/US/docs/interfaces_modules/port_adapters/install_upgrade/multichannel_serial/multichannel-dsi.pri_install_config/3525conf.html),
the interface name for a 7206 would be "serial <slot>/0:0," however this
does not appear to be a valid interface on my 7206.  Does anyone know how I
can figure out what the interface name really is for the PA?  Or, maybe
someone who has experience with this PA can tell me?

Thanks,

Josh