[c-nsp] 6509/SUP720-3BXL with Enhanced FlexWAN issue.. Any ideas?

[Howard Leadmon]

   Thanks for the tip, but I am already at the most current ROMMON revision
that I am aware of:

>From my RP:

Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISEK9_WAN-M),
Version 12.2(33)SXJ1, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Wed 22-Jun-11 18:03 by prod_rel_team

ROM: System Bootstrap, Version 12.2(17r)SX7, RELEASE SOFTWARE (fc1)


>From my SP:

Cisco IOS Software, s72033_sp Software (s72033_sp-ADVENTERPRISEK9_WAN-M),
Version 12.2(33)SXJ1, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Wed 22-Jun-11 18:47 by prod_rel_team

ROM: System Bootstrap, Version 8.5(4)


Also does anyone know if any issues with an older version of the Enhanced
FlexWAN hardware?    As from a show module on the card:

Mod Ports Card Type                              Model              Serial
No.
--- ----- -------------------------------------- ------------------
-----------
  9    0  2 port adapter Enhanced FlexWAN        WS-X6582-2PA
XXXXXXXXXXX

Mod MAC addresses                       Hw    Fw           Sw
Status
--- ---------------------------------- ------ ------------ ------------
-------
  9  0011.2075.d100 to 0011.2075.d13f   1.3   12.2(33)SXJ1 12.2(33)SXJ1 Ok


Also from a show inventory:

NAME: "9", DESCR: "WS-X6582-2PA 2 port adapter Enhanced FlexWAN Rev. 1.3"
PID: WS-X6582-2PA      ,                     VID: V03, SN: XXXXXXXXXXX

NAME: "module 9/0", DESCR: "Serial T3+ Port Adapter"
PID: PA-2T3+           ,                     VID: , Board revision A0, SN:
XXXXXXXX   

NAME: "module 9/1", DESCR: "Multi-channel T1/PRI with CSU"
PID: PA-8MCT1-CSU      ,                     VID: , Board revision C0, SN:
XXXXXXXX   



I mention this, as I have a 6509 over at a clients with an Enhanced FlexWAN,
but  as I can see, it's a much newer version:

Mod Ports Card Type                              Model              Serial
No.
--- ----- -------------------------------------- ------------------
-----------
  7    0  2 port adapter Enhanced FlexWAN        WS-X6582-2PA
YYYYYYYYYYY

Mod MAC addresses                       Hw    Fw           Sw
Status
--- ---------------------------------- ------ ------------ ------------
-------
  7  0013.60cf.4a00 to 0013.60cf.4a3f   2.0   12.2(33)SXJ  12.2(33)SXJ  Ok

NAME: "7", DESCR: "WS-X6582-2PA 2 port adapter Enhanced FlexWAN Rev. 2.0"
PID: WS-X6582-2PA      ,                     VID: V05, SN: YYYYYYYYYYY


Anyway, if you or anyone has any other thoughts or suggestions, I for sure
open to them...



---
Howard Leadmon - howard at leadmon.net

> -----Original Message-----
> From: Daniel Husand [mailto:daniel at fnutt.net]
> Sent: Sunday, July 10, 2011 2:51 PM
> To: cisco-nsp at puck.nether.net
> Cc: Howard Leadmon
> Subject: Re: [c-nsp] 6509/SUP720-3BXL with Enhanced FlexWAN issue.. Any
> ideas?
> 
> On 10/7/11 10:46 , Howard Leadmon wrote:
> >
> >    Maybe I have I have a defective board, but you would think it would
> > kick some nasty errors or something if that was the case.
> 
> Sounds like you are hitting CSCsq77835.
> 
> Resolved Caveats in MSFC3 ROMMON Software Release 12.2(17r)SX6
> 
> .The FlexWAN module configuration is corrupted during a Catalyst 6500
series
> switch or Cisco 7600 series router Cisco IOS router upgrade or during
bootup.
> This problem is resolved in ROMMON software release 12.2(17r)SX6.
> (CSCsq77835)
> 
> --
> Daniel