[c-nsp] Boot from TFTP

[Murphy, Jay, DOH]

Even though you reformat the CompactFlash card, you will need to use "squeeze" to recoup the memory space.

~Jay Murphy 
Sr. IP Network Specialist
NM State Government
 
IT Services Division
PSB – IP Network Management Center
Santa Fé, New México 87505 
"We move the information that moves your world." 
“Engineering is about finding the sweet spot between what's solvable and what isn't."
“Good engineering demands that we understand what we’re doing and why, keep an open mind, and learn from experience.”
                                                                                                                                                                            Radia Perlman
"If human beings are perceived as potentials rather than problems, as possessing strengths instead of weaknesses, as unlimited rather than dull and unresponsive, then they thrive and grow to their capabilities."
                                                                                                                                                                         
 Please consider the environment before printing e-mail


-----Original Message-----
From: cisco-nsp-bounces at puck.nether.net [mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of Scott Voll
Sent: Friday, June 24, 2011 2:54 PM
To: jm at ilk.net
Cc: cisco-nsp at puck.nether.net
Subject: Re: [c-nsp] Boot from TFTP

Thats what I was forgetting...... I knew there was was something.  I'll see
if I can find a Boot helper image to replace the full blown one that is
currently on the flash.

Thanks

Scott

On Fri, Jun 24, 2011 at 1:47 PM, Juergen Marenda <jm at ilk.net> wrote:

>
> You need some RAM...
> The (first) image in FLASH will be loaded started and uncompresses itself.
> It reads the config file and, after configuring some of the interfaces,
> loads the indicated IOS thru tftp into RAM to uncompress and start it.
>
> So you need RAM for two IOS's unziped...
> or a smaller, older, not full-featured Image for booting purposes
> (for some mashines exist boot-helper images).
>
> Why dont you
>
> - boot device
>  and get ip address
>  ...int gig 0/0
>  ip address dhcp
>  no shut
> - ping tftp server
> (ok)
> - format flash:  to clear it
>  or delete some big files (not the vlan.dat ) to make sufficient space
>  for the wanted IOS
> - copy tftp:/ip/file flash:/file
> - reload from flash
> - (probably you want to delete or update the LIST of boot system and boot
> config
>   cammands, if there is more than 1 of each they all will get executed.)
>
> > -----Original Message-----
> > From: cisco-nsp-bounces at puck.nether.net
> > [mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of Scott Voll
> > Sent: Friday, June 24, 2011 10:24 PM
> > To: cisco-nsp at puck.nether.net
> > Subject: [c-nsp] Boot from TFTP
> >
> > OK... I'm in a pinch and I need to upgrade a 2821 to a newer
> > ISO and don't
> > have time to get a new Flash card.
> >
> > So i'm trying to boot from TFTP.  But I keep getting a file
> > to large error
> >
> > %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0/0 assigned
> > DHCP address
> > 10.14.1.53, mask 255.255.255.0, hostname Router
> >
> > %SYS-6-READ_BOOTFILE_FAIL: tftp://
> > 10.14.1.108/c2800nm-advipservicesk9-mz.151-3.T1.bin File read
> > failed -- Not
> > enough space.
> >
> > %SYS-6-READ_BOOTFILE_FAIL: tftp://
> > 10.14.1.108/c2800nm-advipservicesk9-mz.151-3.T1.bin File read
> > failed -- Not
> > enough space.
> >
> > %SYS-6-READ_BOOTFILE_FAIL: tftp://
> > 10.14.1.108/c2800nm-advipservicesk9-mz.151-3.T1.bin File read
> > failed -- Not
> > enough space.
> >
> > %SYS-3-IMAGE_TOO_BIG: 'tftp://
> > 10.14.1.108/c2800nm-advipservicesk9-mz.151-3.T1.bin' is too large for
> > available memory (51691544 bytes).
> > %SYS-6-READ_BOOTFILE_FAIL: tftp://
> > 10.14.1.108/c2800nm-advipservicesk9-mz.151-3.T1.bin File read
> > failed -- Not
> > enough space.
> >
> >
> > Config looks like this:  boot system tftp://
> > 10.14.1.108/c2800nm-advipservicesk9-mz.151-3.T1.bin
> >
> > Memory needed is 512mb  I have "Cisco 2821 (revision 53.50) with
> > 776192K/10240K bytes of memory."  so I should have enough ram.
> >
> > What am I missing?
> >
> > Scott
> > _______________________________________________
> > cisco-nsp mailing list  cisco-nsp at puck.nether.net
> > https://puck.nether.net/mailman/listinfo/cisco-nsp
> > archive at http://puck.nether.net/pipermail/cisco-nsp/
> >
>
>
_______________________________________________
cisco-nsp mailing list  cisco-nsp at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/