[c-nsp] Setting line encoding, no controller present

[Joseph Mays]

I need to set the t1 controller for the serial interface below to be b8zs encoding and clock source internal, but the router does not even recognize the controller commands, and I can't find any relevant commands under the serial interface config.

=====

gw1.office#show controller serial2/0
Interface Serial2/0
Hardware is Quicc 68360 with Integrated FT1 CSU/DSU module
 TX and RX clocks detected.
idb at 0x6416E310, driver data structure at 0x64175A34
WIC interrupt reg = F
SCC Registers:
General [GSMR]=0x2:0x00000030, Protocol-specific [PSMR]=0x8
Events [SCCE]=0x0000, Mask [SCCM]=0x001F, Status [SCCS]=0x0002
Transmit on Demand [TODR]=0x0, Data Sync [DSR]=0x7E7E
Interrupt Registers:
Config [CICR]=0x00C9CF00, Pending [CIPR]=0x00000000
Mask   [CIMR]=0xC000C000, In-srv  [CISR]=0x00000000
SDMA Registers:
[SDSR]=0x00, [SDAR]=0x07A014E0, [SDCR]=0x0772
Command register [CR]=0x600
Port A [PADIR]=0x0000, [PAPAR]=0xFFFF
       [PAODR]=0x0000, [PADAT]=0xEEFD
Port B [PBDIR]=0x0011FE, [PBPAR]=0x00000E
       [PBODR]=0x000000, [PBDAT]=0x03EE5C
Port C [PCDIR]=0x000E, [PCPAR]=0x0000
       [PCSO]=0x0020,  [PCDAT]=0x0FCF, [PCINT]=0x0001
BRGC1 = 0x0000 , BRGC2 = 0x0000
BRGC3 = 0x0000 , BRGC4 = 0x0000
Receive Ring
        rmd(3D010420): status 9000 length 2 address 7B99024
        rmd(3D010428): status 9000 length F address 7B9B724
        rmd(3D010430): status 9000 length 2 address 7B9C424
        rmd(3D010438): status 9000 length 10 address 7B9AA24
        rmd(3D010440): status 9000 length 12 address 7B996A4
        rmd(3D010448): status 9000 length 11 address 7B99D24
        rmd(3D010450): status B000 length F address 7B9A3A4
Transmit Ring
        tmd(3D010458): status 5C00 length E address 7A01894
        tmd(3D010460): status 5C00 length E address 7C14B34
        tmd(3D010468): status 5C00 length E address 7A014D4
        tmd(3D010470): status 5C00 length E address 7C161B4
        tmd(3D010478): status 5C00 length E address 7C15DF4
        tmd(3D010480): status 5C00 length E address 7A00AD4
        tmd(3D010488): status 7C00 length E address 7C14634

tx_limited=1(2)

SCC GENERAL PARAMETER RAM (at 0x3D010C00)
Rx BD Base [RBASE]=0x420, Fn Code [RFCR]=0x18
Tx BD Base [TBASE]=0x458, Fn Code [TFCR]=0x18
Max Rx Buff Len [MRBLR]=1548
Rx State [RSTATE]=0x18008240, BD Ptr [RBPTR]=0x440
Tx State [TSTATE]=0x18000348, BD Ptr [TBPTR]=0x458

SCC HDLC PARAMETER RAM (at 0x3D010C38)
CRC Preset [C_PRES]=0xFFFF, Mask [C_MASK]=0xF0B8
Errors: CRC [CRCEC]=0, Aborts [ABTSC]=9, Discards [DISFC]=0
Nonmatch Addr Cntr [NMARC]=0
Retry Count [RETRC]=0
Max Frame Length [MFLR]=1608
Rx Int Threshold [RFTHR]=0, Frame Cnt [RFCNT]=65524
User-defined Address 0000/0000/0000/0000
User-defined Address Mask 0x0000


buffer size 1524
QUICC SCC specific errors:
131355 input aborts on receiving flag sequence
0 throttles, 0 enables
0 overruns
0 transmitter underruns
0 transmitter CTS losts
20703 aborted short frames