[c-nsp] Lot of input errors on a NPE-G1 interface

gal.9430 at googlemail.com gal.9430 at googlemail.com
Wed May 23 15:33:05 EDT 2012


Hi,

thanks all for the input.

Increasing the hold-queue (from default to 100) doesn't seem to help at all:

GigabitEthernet0/1 is up, line protocol is up
  Hardware is BCM1250 Internal MAC, address is 0006.52f4.d81b (bia
0006.52f4.d81b)
  Internet address is x.x.x.x/28
  MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 2/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  Full-duplex, 1000Mb/s, link type is autonegotiation, media type is SX
  output flow-control is XON, input flow-control is XON
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:00:00, output 00:00:00, output hang never
  Last clearing of "show interface" counters 02:17:11
  Input queue: 0/100/742/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 10536000 bits/sec, 1824 packets/sec
  5 minute output rate 6813000 bits/sec, 2121 packets/sec
     11770910 packets input, 2922271410 bytes, 0 no buffer
     Received 215 broadcasts, 0 runts, 0 giants, 0 throttles
     341 input errors, 0 CRC, 0 frame, 341 overrun, 0 ignored
     0 watchdog, 4242 multicast, 0 pause input
     0 input packets with dribble condition detected
     14975201 packets output, 1820911878 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     137 unknown protocol drops
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 pause output
     0 output buffer failures, 0 output buffers swapped out

Will go from 100 to 150 and see whats happen.



On Wed, May 23, 2012 at 9:27 PM, Phil Mayers <p.mayers at imperial.ac.uk> wrote:
> On 05/23/2012 08:18 PM, Chris Gotstein wrote:
>>
>> %Warning: portfast should only be enabled on ports connected to a single
>> host. Connecting hubs, concentrators, switches, bridges, etc… to this
>> interface when portfast is enabled, can cause temporary bridging loops.
>>
>> My understanding of this was a router would be included as well since
>> it's used to connect multiple hosts.
>
>
> If you don't enable portfast, you have to suffer the STP state transitions,
> which lead to delays in traffic forwarding after link-up.
>
> Portfast basically means: "This port is unlikely to be connected to another
> bridge or hub, so skip the LISTENING/LEARNING transitions and jump straight
> to forwarding; if it goes wrong, STP will close the loop shortly."
>
> It's not magic; and it should be enabled on all host ports. Routers are
> hosts, at layer2.
>
> _______________________________________________
> cisco-nsp mailing list  cisco-nsp at puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-nsp
> archive at http://puck.nether.net/pipermail/cisco-nsp/



More information about the cisco-nsp mailing list