[c-nsp] VPLS ASR1k - ME3800 - no L2 tunnelling ?

[Adam Vitkovsky]

Have you enabled L2PT please?
Cmd: "l2protocol tunnel" under the interface or service inetance. 


adam
-----Original Message-----
From: cisco-nsp [mailto:cisco-nsp-bounces at puck.nether.net] On Behalf Of
Chris Russell
Sent: Tuesday, August 20, 2013 6:28 PM
To: cisco-nsp at puck.nether.net
Subject: [c-nsp] VPLS ASR1k - ME3800 - no L2 tunnelling ?

Hi All

  I`m playing in the lab and I`m struggling with achieving a full L2 tunnel
over VPLS between an ME3800-X and ASR1004.

  Ascii Diagram: 3560[1] - ME3800X -> MPLS <- ASR1004 - 3560[2]

  Essentially, I`m trying to l2 tunnel vtp/cdp/stp over a VPLS connection
between the ME and ASR. LDP is Up, L2 VFI is Up, I can ping from vlan 1 on
3560[1] to vlan 1 on 3560[2] so the VPLS is essentially up.

  That's where the issues start:

  STP traffic is not being passed, both switches are root bridges.

  If I configure 3560[1] as VTP server, 3560[2] does not get any new vlans.
  If I configure 2560[2] as a VTP Server, 3560[1] DOES get new vlans.

  (so VTP tunnelling works from the ASR to the ME3800, but not vice
versa)

  CDP wise, I see nothing from 3560[1] (expected as the ME is configured to
tunnel all), but I see the ASR from 3560[2]

  Stumped ? has anyone done anything similar ? its only untagged traffic
(CDP/VTP/STP) I`m seeing issues with - but that's essentially what I need :)

  The issue looks to the ASR, if I connect both 3560's to ports within the
service-instance on the ME3800-X CDP, etc works, but I can't find any
command that IOS-XE will accept to do the l2 tunnelling on the ASR.

  Config references a single neighbour but in truth this would be multiple,
this is just a lab.

  Config from the ME:

Cisco IOS Software, ME380x Software (ME380x-UNIVERSALK9-M), Version
15.2(2)S, RELEASE SOFTWARE (fc1) - Metro Agg and Scaled Metro Agg Licenses,
Metro Eth


interface GigabitEthernet0/24
  Descr to 3560[1]
  switchport trunk allowed vlan none
  switchport mode trunk
  mtu 9216
  service instance 1 ethernet
   encapsulation untagged , dot1q 1-4094
   l2protocol tunnel
   bridge-domain 100
  !
end

  l2 vfi test1 manual
  vpn id 1
  bridge-domain 100
  neighbor 1.1.1.1 encapsulation mpls


interface Vlan100
  no ip address
  xconnect vfi test1



-- Config from the ASR:

Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M),
Version 15.3(1)S, RELEASE SOFTWARE (fc4)


interface GigabitEthernet0/0/7
  Descr connected to 3560[2]
  no ip address
  negotiation auto
  cdp enable
  service instance 100 ethernet
   encapsulation untagged , dot1q 1-4094
   bridge-domain 100
  !

bridge-domain 100
(ASR accepts the member config but doesn't show it)

l2 vfi test1 manual
  vpn id 1
  bridge-domain 100
  neighbor 2.2.2.2 encapsulation mpls


  There is a command on the ASR l2 vfi to forward l2protocol, but this 
errors not with BPDU tunnel not supported.  Config guides especially 
from IOS-XE reference using l2vpn - but half of the commands on the 
guide, despite this being for the correct software don't exist.

  Any assistance appreciated, head broken :-/

Chris



_______________________________________________
cisco-nsp mailing list  cisco-nsp at puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/